background image

2

XN300 switch XN-332-5ETH-UMS

InstructIon manual

   MN050011EN   August 2022   www.eaton.com

Ethernet connections

The XN-332-5ETH-UMS can be used to connect multiple 

network segments (ETH1–ETH5) using the five RJ45 

ports (X1–X5). Each of these ports features an LA (Link 

Active) LED that signals the port’s connection status and 

an FD (Full Duplex) LED that shows which data transfer 

mode is currently selected. The data transfer rate for the 

XN300 10/100BASE-T Ethernet switch is set automatically 

depending on the data transfer rate required by the device 

with which it is currently communicating: 10 Mbit/s in  

half-duplex mode or 100 Mbit/s (Fast Ethernet) in  

full-duplex mode.
The maximum distance per network segment is 100 m.

X1…X5

Pin

Function

8
7
6
5
4
3
2
1

1

Tx+/Rx+

2

Tx–/Rx–

3

Rx+/Tx+

4, 5

6

RX–/Tx–

7, 8

LED status indicators

The device’s status LEDs are located underneath the front 

cover and can be seen underneath the corresponding labels 

when they light up.

Table 1 .  LED meanings

lED

color

Ethercat 

status

Description

RN (run)

Yellow

Continuous light

The XN300 switch is in the RUN 

state and is ready for operation.

AUS

The XN300 switch is not ready  

for operation.

DC (direct 

current)

Green

Continuous light

Power supply OK.

AUS

Voltage below the  

permissible limit.

LA (Ethernet 

link active)

Green

Continuous light

Connection between two  

PHYs established.

Flashes

Data is being received or 

transmitted through the  

Ethernet bus.

AUS

INIT

FD (Ethernet 

full duplex)

Yellow

Continuous light

Port working in full-duplex mode.

AUS

Port working in half-duplex mode.

Potential relationship between the components

The XN-332-5ETH-UMS features a contact point that is used 

to establish a functional earth connection to the DIN rail. 

The supply voltage’s ground connection is connected to this 

functional earth.
Common

 

0 V

 

Summary of Contents for XN300

















Reviews: