move back several codes manually by pressing CHANNEL-
several times (if you move back too far press to
move forwards again). When the appliance reacts to the remote
control again, press the ENTER key to complete the installation.
Identification of retrieved codes
1. Press the SETUP key until the LED remains lit. Release the
SETUP key.
2. Press the function key of the appliance whose code you want to
identify (TV, VCR, etc.). The LED flashes once.
3. Press SETUP. The LED flashes once.
4. To find the first digit press keys 0 to 9 until the LED flashes.
The number pressed last is the first digit of the code.
5. Press 0 to 9 as described above to find the second digit.
6. Press 0 to 9 to find the third digit. The LED switches off when
the third digit has been found. The code can be entered on the
appropriate label on the remote control device (battery
compartment).
Learning
The Xanura remote control code library includes codes for most
TVs, videos, etc. If, however, a specific appliance is not included in
the library, the codes can be learned from your existing remote
control device. You may also come across a code that is almost
identical to the functions on your appliance, but with a few keys
missing. These keys can simply be learned.
Learning commands
1. Point your existing remote control at the Xanura remote control
device (front facing front) with a gap of approximately 2.5 cm
between them.
2. Press the SETUP key until the LED remains lit. Release the
SETUP key.
3. Press the function key (TV, CD, SAT, etc.) that corresponds to the
appliance you want to use. The LED flashes once.
4. Press the LEARN key. The LED flashes once.
5. Press the key on the Xanura remote control device under which
a new command is to be learned. The LED flashes once (press
SHIFT first if you intend to use a Shift-based function).
6. Two methods are available, depending on the original type of
remote control device:
a.
Press the key of the existing remote control feature you want to
learn. Keep the key on the original remote control pressed down
until the LED on the Xanura remote control device goes out
briefly.
If the LED does not go out but flashes, you need to use remote
control method b
(Note: if you have just tried method a and want
to change to method b, first go to step 5).
20
MBO 1991 494-401 GA
Xanura™
Remote control device universal, RF and IR type ABX1
b.
Press the key of the existing remote control feature you want to
learn. Keep the key on the original remote control pressed down
as long as you normally would when operating the appliance.
7. Repeat steps 5 and 6 for each key to be learned.
8. Press ENTER when you have finished learning keys.
Erasing learned commands to release memory space
Stored, learned function commands can be erased individually (TV,
VCR, etc.):
1. Press the SETUP key until the LED remains lit.
Release the SETUP key.
2. Press your selected function key (TV, VCR, etc.).
The LED flashes once.
3. Press the LEARN key twice.
4. Press SETUP. The LED goes out after a few seconds.
5. All stored, learned commands of your selected functions have
now been erased.
Notes regarding learning
• Ensure that the batteries in both remote control devices are fully
charged before starting the learning process.
• Remember not to move the remote control devices when
pressing keys.
• Commands cannot be allocated to the Learn, Setup, TV, VCR,
CBL, SAT, CD, PC, M1, M2, ShowView/V+, Xanura keys, or
directly to the SHIFT key.
• Experiment by learning 2 or 3 keys initially (to test compatibility)
before learning the entire keyboard of the original remote control
device.
• The LED will flash for 3 seconds if the memory is full. It can no
longer learn additional keys. Any surplus stored keys can be
erased per mode by erasing the learned commands.
• If the keys on the existing remote control device are not pressed
for as long when learning, more memory space will be available
on the Holec remote control. This also minimises the risk of
codes being learned incorrectly.
• If problems occur during the learning process, experiment with
the distance between the remote control devices.
• On some remote control devices the LED is not positioned in the
centre. Experiment by moving them sideways with respect to
each other.
• Make sure that you are not directly below a strip-light, or in direct
sunlight, during the remote control learning process.
• Use keys L1 and L2 to learn codes for which there are no
corresponding keys on the Xanura remote control device.
• If problems occur when learning the keys, erase the memory and
try again.
21
MBO 1991 494-401 GA
Home Theatre Macro function
The remote control device is equipped with two Macro keys: M1
and M2. These keys can be programmed to complete a series of
commands when the button is pressed once. This powerful feature
is ideal for example to switch on all your audio and video
equipment, or select specific preferential settings in Home Theatre
applications.
Programming Macro keys M1 and M2
1. Press the SETUP key until the LED remains lit. Release the
SETUP key.
2. Press the Macro key you intend to set (M1 or M2)
3. Press the remote control keys that will be stored under the
Macro key (maximum 14 commands). The programming
sequence is copied exactly when the Macro is executed.
4. Press the Macro key again to store the Macro. Programming is
terminated automatically at 14 commands (maximum), and the
14 commands are stored under the Macro key you specified.
Note when setting Macros
The Macro keys can execute both infrared and high frequency
commands. This allows you to switch on your audio and video
equipment and control the lighting simultaneously (using Xanura
modules). Ideal for Home Theatre applications.
Erasing a Macro key
1. Press the SETUP key until the LED remains lit.
Release the SETUP key.
2. Press the Macro key you intend to erase
3. Press the SETUP key again.
22
MBO 1991 494-401 GA
Xanura™
Remote control device universal, RF and IR type ABX1
