![background image](http://html1.mh-extra.com/html/eaton/tripp-lite-series/tripp-lite-series_advanced-users-manual_4236545015.webp)
Tripp Lite Series UPS Systems User Guide 93470A—Rev A
9
C
Chhaapptteerr 33 O
Oppeerraattiioonn
33..11
S
Sttaannddbbyy M
Mooddee
When the UPS is turned off and plugged into a wall outlet or other power source, the UPS is in Standby Mode.
The Power On indicator is off, indicating that power is not available from the rear receptacles.
33..22
TTuurrnniinngg tthhee U
UP
PS
S O
Onn
For normal AC startup of the UPS, follow these steps:
1.
Connect the UPS AC power cord to a properly grounded NEMA 5–15R wall outlet.
2.
Press the power button lightly for two seconds to start the UPS in Normal mode. The green LED will turn
on and stay illuminated. See
for an illustration of the green LED indicator location on
the back panel.
3.
Plug your load equipment into the outlets on the back of the UPS. These outlets provide both surge and
battery backup capabilities.
NOTE
The Tripp Lite Series UPS system is designed to support electronic equipment only. You
will overload the UPS if the total volt-amp (VA) ratings for all the equipment connected to
the outlets exceeds the UPS output capacity. To find your equipment’s VA ratings, look
at its nameplate. If the equipment is listed in amps (A), multiply the number of amps by
120 to determine VA. For example 1A × 120 = 120VA. If you suspect you have
overloaded the outlets, remove some equipment.
4.
Register your UPS at
.
33..33
C
Coolldd S
Sttaarrtt
To turn on the UPS without utility power, hold the ON/OFF button for two seconds. The green LED will flash
every ten seconds, indicating it is on battery power.
NOTE
The UPS does not automatically detect the input frequency when starting on the
battery. The default frequency for 120V models is 60 Hz.
33..44
TTuurrnniinngg tthhee U
UP
PS
S O
Offff
To turn off the UPS, hold the ON/OFF button on the front panel for two seconds and then unplug the UPS from
the power source. If you do not unplug the UPS, it remains in Standby Mode.
33..55
A
Auuddiibbllee A
Allaarrm
m EEnnaabbllee//D
Diissaabbllee
The UPS audible alarm controls operate independently from Line Mode to Battery Mode and can be enabled or
disabled in the following modes of operation:
Line Mode
NOTE
The default setting for the Line Mode alarm tone is enabled.
•
To permanently disable
all the alarm tones for Line Mode and in Battery Mode, press and hold the power
button for ten seconds. The red LED will flash, and the UPS alarm tone will sound, indicating the alarm is
now disabled.
•
To enable
the alarm tone in Line Mode, press and hold the power button for ten seconds. The green LED
will flash, and the UPS alarm tone will sound, indicating the alarm is enabled.
Summary of Contents for TRIPP LITE Series
