background image

S611 Soft Starter

S611 Soft Starter

    MN03901003E—January 2012    www.eaton.com

i

Disclaimer of Warranties and Limitation of Liability 

The information, recommendations, descriptions and safety notations in this document are 
based on Eaton Corporation’s (“Eaton”) experience and judgment and may not cover all 
contingencies. If further information is required, an Eaton sales office should be consulted. 
Sale of the product shown in this literature is subject to the terms and conditions outlined in 
appropriate Eaton selling policies or other contractual agreement between Eaton and the 
purchaser.

THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR 
IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR 
MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING 
CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE 
OBLIGATION OF EATON.  THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME 
PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. 

In no event will Eaton be responsible to the purchaser or user in contract, in tort (including 
negligence), strict liability or otherwise for any special, indirect, incidental or consequential 
damage or loss whatsoever, including but not limited to damage or loss of use of equipment, 
plant or power system, cost of capital, loss of power, additional expenses in the use of 
existing power facilities, or claims against the purchaser or user by its customers resulting 
from the use of the information, recommendations and descriptions contained herein. The 
information contained in this manual is subject to change without notice. 

Cover Photo: S611 Soft Starter

www.comoso.com

Summary of Contents for S611

















Reviews: