RS Enclosure unpacking and initial setup
•
Read and understand the instruction herein before attempting to unpack,
install, operate or service the RS enclosure.
•
Follow all information that is found on safety labels on the product and
packaging.
•
Familiarize yourself with the various enclosure components described
within this manual.
•
Familiarize yourself with the warning symbols that appear throughout
this manual.
•
The use of personal protective equipment such as safety glasses and work
gloves is recommended during the unpacking and set-up of the enclosure.
•
Read, understand and follow the guidelines and limitations herein for
loading your enclosure.
NOTICE
Notice points out something of special interest to the reader
in direct context or relationship to the immediate topic or step
being performed.
WARNING
Warnings draw special attention to any situation that may
cause severe injury, physical harm, or death, to the reader and/
or person performing the task at hand.
Safety Warnings and Precautions
WARNING
Do not apply loads that exceed the capacity of the enclosure. The
stated capacities DO NOT include the weight of the enclosure itself.
The applied load includes any items installed into the enclosure after
receipt of the enclosure from the carrier, including (but not limited
to) electronic equipment, power distribution units, and cabling. The
applied load also includes any item(s) mounted to the outside of the
enclosure or rested on the top of the enclosure, where the enclosure
bears the weight of the items.
It is recommended that you load your heaviest electronic equipment
at the bottom of the enclosure. This will ensure that the load’s center
of gravity (tipping point) is as low as possible.
Failure to follow this
warning could result in the possibility of the enclosure tipping,
causing serious injury or property damage.
Installation and assembly must be performed by qualified personnel.
Ensure that the floor / wall structure is able to withstand the weight
of the enclosure while fully loaded.
Ensure the enclosure is plumb and level for proper operation.
Route all power cords and cabling away from any possible pinch points
or moving parts.
Always fully mount and secure enclosure or rack system before
loading equipment.
Evenly distribute all mounted loads and equipment to ensure stability
within the enclosure system, placing heavier loads towards the bottom
of the enclosure to avoid unstable conditions.
To reduce risk of personal injury and product damage, always
ensure a sufficient amount of personnel are present when loading,
unloading or moving the enclosure or rack system.
Suitable for mounting on concrete or other non-combustible surface only.
Assembly and installation of certain accessories takes place on top
of an enclosure, at an approximate height of 8-11 feet. If step ladders
are used during installation, installers MUST maintain three points of
contact with the ladder at all times, DO NOT climb to a point higher
than six feet from the ground, unless tethered to a safety harness,
and NEVER stand on the top two steps of a step ladder, regardless
of the ladder’s overall height.
Failure to adhere to these warnings may result
in serious injury or property damage.
Before installing Eaton’s RS Enclosure, it is recommended that you do the following:
Disclaimer of warranties and limitation of liability
The information, recommendations, descriptions and safety notations in
this document are based on Eaton Corporation’s (“Eaton”) experience and
judgment and may not cover all contingencies. If further information is
required, an Eaton sales office should be consulted. Sale of the product
shown in this literature is subject to the terms and conditions outlined
in appropriate Eaton selling policies or other contractual agreement
between Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER
THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT
BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE
OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT
SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT
BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract,
in tort (including negligence), strict liability or otherwise for any special,
indirect, incidental or consequential damage or loss whatsoever, including
but not limited to damage or loss of use of equipment, plant or power
system, cost of capital, loss of power, additional expenses in the use of
existing power facilities, or claims against the purchaser or user by its
customers resulting from the use of the information, recommendations
and descriptions contained herein. The information contained in this
manual is subject to change without notice.
Download our complete RS Enclosure installation manual at
http://powerquality.eaton.com/Products-services/Enclosures/Eaton-RS-Enclosures-Server.aspx