Eaton Power Xpert XGIS Instruction Booklet Download Page 69

Page: 69 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 127.

Auxiliary Cabinet
Top Low Voltage
Wireway Top Plate

Auxiliary Cabinet
Lifting Eye Bolts (M12)

Auxiliary cabinet lifting eye holes.

Figure 128.

Vertical Section

Rear side

Vertical Section

End Sheets

Rear Attachment

Angle

Auxiliary Panel

Auxiliary cabinet addition rear view

Attaching an auxiliary panel to either end of a lineup
Every lineup end vertical section has end sheets bolted to its frame.

These end sheets have bolt holes that are used to attach the end

sheet to the vertical section. The bolt holes that usually attach an

end sheet to the vertical section can also be used to attach an

auxiliary cabinet.

Use ten (10) M8x75mm allen head bolts and M8 washers to
attach the auxiliary panel to the vertical section end sheet. See

Figure 129

and

Figure 130

Figure 129.

Front of

Vertical Section

End sheet holes for

10 - M8x75 bolts

with M8 washer

End section with 10 bolt holes available for

auxiliary section.

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands