manualshive.com logo in svg

Eaton Power Xpert XGIS, Instruction Booklet

Share
Download
Eaton Power Xpert XGIS Instruction Booklet Download Page 70

70

Instruction Booklet 

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

TM

XGIS gas insulated switchgear

EATON

 www.eaton.com

Figure 130. 

Aux. section holes for 
10 - M8x75 bolts
with M8 washer

Front of

Vertical Section

  Auxiliary section placed next to vertical section for 

attachment.

 

Attach the L bracket to the adjacent vertical the section and 
the auxiliary section rear panel. The L bracket has ten bolt 

holes on one surface and four bolt holes on it other surface.
Use seven (7) M8x30 bolts to attach the L bracket to the auxil-

iary panel rear wall.
Use four (4) M8x75 bolts to attach the L bracket to the vertical 

section end sheet. See 

Figure 131.

Rear of

Vertical Section

Vertical Section

End Sheets

Rear Attachment

Angle

Auxiliary Panel

7 - M8x30

bolts

4 - M8x75

bolts

Figure 131.   Attach L bracket to vertical section side panel and 

auxiliary section rear panel.

Summary of Contents for Power Xpert XGIS

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands