Menvier40/100
Installation
Page 31
line of the display shows the first in the list of
found and lost devices. Press
to see any
other items in the list.
4.
Either:
Press
to go back into Installer Menu
(so that you can go and check that all the bus
devices you have installed are connected,
powered up and addressed correctly).
Note: To check an expander address remove the
lid and briefly press the addressing button. The
two digit display will show the bus address for a
few seconds.
OR:
Press
to make the control unit update
its internal record of devices attached to the
bus. The display shows:
5. Press
to accept the change to the bus. (You can
still press
to return to the installer menu if you do
not want to change the number of devices on the
bus.)
Note: If you attempt to leave the Installer Menu
when a detector/device tamper is active then the
keypad displays a fault message telling you which
detector/device is causing the problem. Press
to return to the Installer Menu. You must either
close the detector/device tamper or delete it from
the system before you can leave the Installer
Menu.
Important!
Saving Changes
When you make changes to the Installer Menu the
control unit holds those changes in temporary
memory until you leave the Installer Menu. As you
leave the Installer Menu the control unit writes
those changes into a permanent store. If you
remove all power BEFORE you leave the Installer
Menu then the control unit will lose your changes.
Note that this does not apply if you restore
Factory Defaults, that change takes place
immediately.
Re-Entering the Installer Menu
When you enter the Installer Menu from a keypad,
the alarm system is effectively disabled. While the
system is in Installer Menu:
Any other user trying to set the system from a
keypad will see the message “Installer on
Site”.
All Hold Up Devices (including radio HUDs),
fire alarm zones, 24 hour zones and tampers
are disabled.
Note that this does not apply if you are using the
web browser interface from a PC. If you have
logged into the system from a PC then the alarm
system is active.
If you need to re-enter the Installer Menu:
1. Make sure the system is unset and showing
the standby screen (time and date).
2. Key in the Installer access code. At Security
Grade 2 the default Installer access code is
“1234”.
At Security Grade 3 the default Install access
code is “123400”.
As you start to key in the code the display
shows:
When you key in the last digit of the Installer
access code the display shows:
Notes:
1. You will see this screen the first time you enter
the Installer menu on a new control unit, or if you
have restored Factory Defaults. You can disable
this feature by using the Installer menu option
System Options - User Access – User Code Required
.
2. If you set
User Code Required
to NO then the
control unit no longer complies with EN50131.
This option complies with BS8243 only if the user
has given written consent.
3. If you key in an access code incorrectly, the
display shows four “stars”. Key in the code again.
If you key in a total of four incorrect codes then
the system locks you out for 90 seconds.
3. Key in the default user code (see Note
below).
At Security Grade 2 the default user access
code is “5678”. At Security Grade 3 the code
is “567800”.
The display shows:
4. Press
or
to display more items from the
menu.
Each item appears on the bottom line of the
display in turn, for example:
5. Press
to select that item of the menu.
The option you selected now appears on the
top line. If there are any sub-options for that
selection, then the first of them appears on
the bottom line, for example:
You can press
or
to display the other
sub-options.
Defaulting Access Codes
If the User 1 and/or Installer codes are lost then
you must restore all user information to its factory
defaults. All prox tags, remotes and radio HUDs
will be deleted.
1. If possible, enter the Installer menu.
