background image

 

Eaton Small External Battery Cabinet (EBC-S) 
and Large External Battery Cabinet (EBC-L) 

User’s and Installation Guide 

 

© Eaton Corporation plc 2015. All rights reserved.

 

Revision: 002

 

Document ID: P-164000504 

27 (37)

 

 

4.

 

Connect the signal wires and the power cables to the connectors 
according to Figure 5. 

5.

 

Put the front plate back and fasten the screws. 

If multiple cabinets are used, repeat the steps for the rest of the 
cabinets and make sure that the signal wire harnesses are daisy chained 
in the next cabinet. 

To daisy chain signal wires, cut the multiple connector and extra length 
of the cables and connect the cables to TB2 terminals. 

3.5

 

Installation compatibility of the EBCs 

EBC-S and EBC-L are fully compatible with the Eaton 93PS UPS product 
line. Other UPSs may not be fully compatible with the external battery 
cabinets. Refer to the UPS for the requirements for the external battery 
supply. 

3.6

 

Operation 

To set the cabinet on or off, open the cabinet door and flip the power 
switch down or up. See Figure 6 for the breaker. 

 

Figure 6. Breaker 

Summary of Contents for EBC-L






































Reviews: