Eaton Cutler-Hammer QS4500TE0001, Quick Start Instructions

Page: 5 / 8

QS4500TE0001
Page 5
Effective 6.01
Step 6: To view setpoints, press the <Display Select>
pushbutton until the Set Points LED lights. Use the
Table 1 Setpoint Possibilities
Setpoint Setpoint Units Description Range Factory Default
TDES Minutes:Seconds Time Delay Engine Start 0 to 120 seconds 0
TDNE Minutes:Seconds Time Delay Normal to Emergency 0 to 1800 seconds 0
TDEN Minutes:Seconds Time Delay Emergency to Normal 0 to 1800 seconds 0
TDEC Minutes:Seconds Time Delay Engine Cooloff 0 to 1800 seconds 0
NOMF Volts Nominal Frequency 50 or 60 Hz As ordered
NOMV Volts Nominal Voltage 120 to 600 volts As ordered
1UVD Volts Source 1 Undervoltage Dropout 97% to 50% of NOMV 80% of NOMV in volts
2UVD Volts Source 2 Undervoltage Dropout 97% to 50% of NOMV 80% of NOMV in volts
1UVP Volts Source 1 Undervoltage Pickup 99% to (1UVD + 2%) 90% of NOMV in volts
2UVP Volts Source 2 Undervoltage Pickup 99% to (2UVD + 2%) 90% of NOMV in volts
1OVD Volts Source 1 Overvoltage Dropout 105% to 120% 115% of NOMV in volts
2OVD Volts Source 2 Overvoltage Dropout 105% to 120% 115% of NOMV in volts
1OVP Volts Source 1 Overvoltage Pickup (1OVD - 2%) to 103% 110% of NOMV in volts
2OVP Volts Source 2 Overvoltage Pickup (2OVD - 2%) to 103% 110% of NOMV in volts
1UFD Hertz Source 1 Underfrequency Dropout 90% to 97% of NOMF
2UFD Hertz Source 2 Underfrequency Dropout 90% to 97% of NOMF
1UFP Hertz Source 1 Underfrequency Pickup (1UFD + 1Hz) to 99%
2UFP Hertz Source 2 Underfrequency Pickup (2UFD + 1Hz) to 99%
1OFD Hertz Source 1 Overfrequency Dropout 103% to 110% of NOMF
2OFD Hertz Source 2 Overfrequency Dropout 103% to 110% of NOMF
1OFP Hertz Source 1 Overfrequency Pickup (1OFD - 1Hz) to 101%
2OFP Hertz Source 2 Overfrequency Pickup (2OFD - 1Hz) to 101%
TDN Minutes:Seconds Time Delay Neutral 0 to 120 seconds 0
TDNLD Load Decay Neutral 0=Disable, 1=Enable 0
LDCY Volts Load Decay Voltage 10% to 30% of NOMV 10%
PRFSRC Preferred Source 0=None, 1-Src1, 2=Src2 1
EXER Clock Exerciser 0=Disable, 1=Enable 0
EXLD Exercise Load Transfer 0=Disable, 1=Enable 0
PEDAY Exercise Day 1 to 7 (1=Sunday)
PEH Clock Exercise Hour 12am to 11pm
PEMIN Clock Exercise Minute 00 to 59
MANTR Retransfer Mode 0=Automatic, 1=Manual 0
CTDNE Commit/No Commit 0=Not, 1=Commit
TMODE Engine Test Mode (Pushbutton) 0=No Load, 1=Load, 0
2=Disable
TER Hours:Minutes Engine Test/PE Run Time 1 minute to 10 hours 1
TPRE Minutes:Seconds Pre Transfer Signal Time 0 to 120 seconds 0
GENNO Number of Generators 0=Dual Utility, 1
1=One (Source 2)
2=Dual Generator
PHASE Phases 1 or 3 As Ordered
TSEQ Minutes:Seconds Time Delay Load Sequencing 0 to 120 seconds 0
PT PT Ratio 2 (2:1) to 500 (500:1) 2
TDEF Seconds Time Delay Engine Fail 0 to 6 seconds 0
<Step> pushbutton to step through the set points
(Figure 6 and Table 1).