background image

IB01602007E

For more information visit: www.cutler-hammer.eaton.com

Instruction Bulletin

Effective:  June 2003

Page

 23

O&M Manual for 
Non-Automatic Transfer 
Switches (30 – 1200 Amperes)

5.4  Non-Automatic Operation (Electrically Operated)

A non-automatic (electrically operated) transfer switch 
(Section 1.2.1) functions similarly to the non-automatic 
(manually operated) transfer switch except for the addition 
of an electrical operating feature. This feature permits the 
main contacts to be opened or closed electrically. There is, 
however, no intelligence circuit associated with this design.

Electrical operation is accomplished by adding a motor and 
required circuitry to the manual mechanism and wiring it 
to a selector switch on the front of the enclosure (Figure 22). 
The switch’s operating position can be visually indicated 
on the front of the enclosure by using indicating lights.

Since an intelligence circuit is not part of the design, 
operation of the selector switch is required each time an 
electrical transfer is required, whether it is from Source 1 
to Source 2 or vice versa.

Figure 22. Electrical Operation Pushbutton and Position Indicating 
Lights Shown Mounted

Summary of Contents for Cutler-Hammer NTV Series





























Reviews: