background image

6

Instructional Leaflet

RLY-800 Radio Frequency Relay (Brazil)

Mounting Options for the RLY-800

The RLY-800 is designed to be mounted in any of 
these configurations:

Wall mounted

Vertical pole mounted (utility pole)

Horizontal pole mounted (light pole arm)

These mounting options can be used regardless of 
whether the RLY-800 uses an internal or external 
antenna.

A RLY-800 with an internal antenna or a remote 
external antenna can be mounted as follows: 

Wall mounted

Pole mounted vertically

Facing downward on a light pole arm

Figure 4. Internal Antenna and Remote External 

Antenna Device Mounting Options

A RLY-800 with an external, attached antenna can 
be mounted as follows: 

Wall mounted

Pole mounted horizontally

Horizontally on the side of a light pole arm

Figure 5. External Attached Antenna Device 

Mounting Options

Lag Bolts 
(Shown) or 
Band Clamps

Band Clamps

Up

Wall/Vertical 
Pole Mounting

Light Pole 
Arm Mounting

CAUTION:

As shown in 

Figure 5

, RLY-800’s that

utilize an external attached antenna must be
oriented so that the antenna is pointing towards the
ground. Mounting the RLY-800 with the antenna on
top of the box may cause moisture to enter the
RLY-800.

Lag Bolts 
(Shown) or 
Band Clamps

Band Clamp

Band Clamp

Up

Horizontal 
Pole Mounting

Light Pole 
Arm Mounting

NOTE: 

The 

Antenna must 
be located on 
the bottom of 
the RLY-800.

NOTE: 

The 

Antenna must 
be located on 
the bottom of 
the RLY-800.

Summary of Contents for Cooper Power Systems RLY-800















Reviews: