background image

41

SPEAR™ Single-Phase Recloser System

INSTALLATION AND OPERATION INSTRUCTIONS

   MN280048EN   June 2016

12.  Perform a battery test on the new battery (assuming it 

has been adequately charged) to confirm the state of 

the new battery and wire assembly connections. Refer 

to the 

Battery test and charging procedures

 section.

Return the control to service

After the required work is completed, proceed as follows:
1.  Remove AC power from the control.
2.  Disconnect the control battery.
3.  Disconnect the control from the test set.
Follow this procedure to return the control to service:
1.  Appropriate personnel must verify that all control 

settings are correct.

2.  Reconnect the ground cable to the control.
3.  Control cable properly connected, fully tightened to 

ensure gasket seal, and supported on both ends.

4.  Plug in the control battery.

otee:

N

The SPEAR single-phase recloser control will not 

automatically power up until AC power is applied.

5.  Apply AC power to the control.
6.  Verify the control clock is set to the current time after 

AC power has been reapplied.

otee:

N

The control clock may require resetting if the 

operating power has been disconnected for more 

than thirty days. Refer to 

Service Information 

MN280012EN SPEAR Single-Phase Recloser Control 

Programming Guide

 for information on setting the 

control clock.

Figure 44 . 

Wing 

nut

Wing 

nut

Wing 

nut

Reinstall wing nuts and battery bracket

Additional information

 CAUTION

This equipment requires routine inspection and 

maintenance to ensure proper operation . If it is not 

maintained, it can fail to operate properly . Improper 

operation can cause equipment damage and possible 

personal injury . 

G105 .1

Replacement kits

Replacement parts kits for the SPEAR single-phase 

recloser control are available through the factory Service 

Department. Only factory-authorized parts are to be used. 

To order replacement parts, refer to 

Parts Guide S260-01 

through S280-01

 for catalog numbers. Contact your Eaton 

representative for additional information and ordering 

procedures.

Factory-authorized service centers

Factory-authorized service centers are located throughout 

the continental United States to provide maintenance, repair 

and testing services for Eaton’s Distribution Switchgear 

products. Refer to 

Service Centers Brochure B100-04009

 for 

the Authorized Service Center closest to your location. For 

further information, contact your Eaton representative.

Factory maintenance classes

The factory service department offers a basic testing 

and troubleshooting course for the SPEAR single-phase 

recloser system. This course, taught by experienced 

service technicians, is held at the factory’s in-house training 

facility. For additional information, contact your Eaton 

representative.

Type MET recloser control tester

A 30-minute video program KSPV7 Kyle Type MET Electronic 

Recloser Control Tester Operation and Testing Procedures 

is available as a supplemental training aid for service 

personnel.

Summary of Contents for COOPER POWER SERIES
















































Reviews: