background image

Parallel-groove terminal (Terminal code - C)

1.  Align the circular hole of the spade adapter with the 

tapped center hole of the Companion II fuse. 

2.  Place the internal-tooth lock washer onto the bolt, and 

insert the bolt through the spade adapter hole into the 

tapped center hole of the fuse (as shown in Figure 8) 

and torque the bolt to 10-15 ft-lbs.

3.  Assemble carriage bolt, terminal clamp, split lock 

washer and hex nut on the spade adapter as shown in 

Figure 9.

Spade terminal (Terminal code - D)

1.  Align the circular hole of the spade adapter with the 

tapped center hole of the Companion II fuse. 

2.  Place the internal-tooth lock washer onto the bolt and 

insert the bolt through the spade adapter hole into the 

tapped center hole of the fuse and torque the bolt to 

10-15 ft-lbs. (Figure 10.)

Spline stud terminal (Terminal code - G)

1.  Insert threaded end of the spline stud into the tapped 

center hole of the Companion II fuse and torque spline 

stud to 10-15 ft-lbs. (Figure 11.)

Offset adapter (Terminal code - J)

1.  Align the hole of the offset adapter with the tapped 

center hole of the Companion II fuse. 

2.  Place the washer onto the bolt and insert the bolt 

through the hole of the offset adapter into the tapped 

center hole of the fuse and torque the bolt to 10-15 

ft-lbs. (Figure 12.)

Figure 9. Parallel-groove terminal.

2.0"

(51 mm)

SPADE

ADAPTER

TERMINAL CLAMP

HEX NUT

CARRIAGE BOLT

BOLT

SPLIT LOCK 

WASHER

INTERNAL-

TOOTH 

LOCK 

WASHER

Figure 10. Spade terminal.

2.0"

(51 mm)

0.41" (10.4 mm)

SQUARE HOLE

BOLT

SPADE

ADAPTER

INTERNAL-

TOOTH 

LOCK 

WASHER

Figure 11. Spline stud terminal.

2.44"

(62 mm)

Figure 12. Offset adapter terminal.

3.8" 

(97 mm)

OFFSET 

ADAPTER

0.8" 

(20 mm)

BOLT

WASHER

5

COMPANION II BACK-UP CURRENT-LIMITING FUSE INSTALLATION INSTRUCTIONS

    MN132009EN   

Summary of Contents for Companion II back-up current-limiting fuse













Reviews: