background image

9

EATON Char-Lynn  

Power Steering Control Unit Series 5 Parts and Repair  C-STCU-TS002-E1  November 2006

Round Housing
with End Ports

Parts List

ITEM NO.

PART NO.

QTY.

DESCRIPTION

REFERENCE PAGE

See Table 4.0 

Cap Screw, Hex Head 

10

2 4993924-XXX 

Cap, End (Non-load sense, non-STC only)

See Table 4.0 

Gerotor, Sub-assembly 10

5 4993805-001 

Wear Plate

6 4994693-001 

Drive

9 22853-000 1 

Drive Pin

13 4997396-001 

Bearing Race

14 4996933-001 

Bearing, Needle Thrust

16 4997708-001 

Dust 

Seal

REPLACEMENT PART NO.

DESCRIPTION

64456-00

Centering Spring Kit - Standard Torque (contains parts with *)

990170-000

Centering Spring Kit - Low  Torque (contains parts with **)

990252-000

Seal Kit - Standard Back Pressure (contains parts with **)

9900256-000

Seal Kit - High Back Pressure (contains parts with **)

9900321-000

Seal Kit - Viton, PM Gerotor (contains parts with **)

9900323-000

Seal Kit - Viton, Steel Gerotor (contains parts with **)

Table 3.0

Round Housing with 
End Ports

ACTUAL DISPLAY

REFERENCE NO. 4 GEROTOR

REFERENCE NO. 29 CAP SCREW

cm

3

/r [in

3

/r]

Part No.

Width mm [in]

Part No.

Length mm [in]

31.5 [1.92] 

4998582-001 

7.4 [.290] 

4994536-045 

44.9 [1.77]

39.5 [2.41] 

4998582-002 

9.3 [.366] 

4994536-050 

50.0 [1.97]

50.8 [3.10] 

4998582-003 

8.3 [.326] 

4994536-045 

44.9 [1.77]

63.1 [3.85] 

4998582-004 

10.2 [.400] 

4994536-050 

50.0 [1.97]

73.8 [4.50] 

4998582-005 

12.1 [.476] 

4994536-050 

50.0 [1.97]

100 [6.10] 

4998582-006 

16.3 [.642] 

4994536-055 

55.1 [2.17]

120 [7.33] 

4998582-007 

19.5 [.768] 

4994536-060 

59.9 [2.36]

Table 4.0

Gerotor

Summary of Contents for Char-Lynn















Reviews: