2.
Brightness, Contrast, Hue, Saturation,
Sharpness can be adjusted here. The
available values are: -4, -3, -2, -1, 0, 1, 2, 3,
4
3.
AGC: The sensitivity of the camera can
be adjusted to the environmental lighting. By
enabling this function the camera will get
brighter images on low light, but the level of
noise may also increase. The available
values are: 16x, 24x, 32x, 48x.
4.
Shutter Time: Choose the location of
your camera or a fixed shutter time. The
shorter the shutter time is the less light the
camera receives and the image becomes
darker.
Note
: When you select a number in Shutter
Time, the shutter time will vary in a range
and be controlled by camera automatically.
The following table shows the shutter time
options and corresponding range.
5.
Sense up: When enabled, provides a
higher sensitivity in low light conditions by
slowing the shutter speed. The available
values are: 1/30, 1/15, 1/10, 1/5.
6.
D-WDR: This function enables the
camera to reduce the contrast in the view to
avoid dark zones as a result of over and
under exposure. If the Input resolution is
30fps, the default value is fixed on
ENABLED. The available values are: OFF, 1,
2, 3, 4, 5, 6, 7, 8. If the D-WDR is enabled
the values for bright, dark and contrast can
be adjusted.
7.
Anti Fog: Improve the image clarity on
environments presenting high levels of fog or
smoke.
8.
Lens Distortion Correction: Straight the
curves in the borders of the image caused by
the lens angles. The available values are:
OFF, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10.
9.
Video Orientation: Flip or mirror the
image.
10. Day & Night: The camera can detect
the light level of the environment. If you
choose Light Sensor Mode, the image will be
turned black and white at night in order to
keep a clear image. To set light sensor mode,
appoint a Lux standard of switching D/N. The
current Lux value is provided for reference.
Under Times Mode the switch time of Color /
Black and white will be according to the given
time. You can also control it by choosing Color
or B/W.
11. Red / Blue gain: Set the values for Red /
Blue gain. The available values are: -5, -4, -3, -
2, -1, 0, 1, 2, 3, 4, 5
12. Denoise: This function is able to filter the
noise and blur from the image and show a
clearer view. You can set the values for 2D and
3D filters.
User Management
The installer can change the default username
& password, create and remove users.
Wireless Setting
The installer can change and connect the
camera to a Wi-Fi network, the camera will
display the available networks and their SSID’s
and the required level of security.
IP Setting
The installer can change the IP assignment
mode to and from DHCP or Static. When Static
is selected then the options displayed below
can all be manually edited.
Please Note
: It is advised that if the IP address
is assigned via DHCP that the IP assignment
mode is changed to Static to retain the IP
address should there be a loss of power to the
camera or the router.
Log list
The installer can view the system log of the
camera.
Factory Default
If you forget your password, please follow the
steps to revert back to default value.
1.
Remove the power and Ethernet cable.
2.
Unscrew and remove the lid from covering
the access to the default button. It is
recommended that you use a small piece of
copper wire to reach it inside the hole. Press
and hold the button once it is reached.
Option
Shutter Time Range (sec.)
Outdoor 1/33000 ~ Selected number in
Sense-up
Indoor
NTSC: 1/120 ~ Selected number in
Sense-up
PAL: 1/100 ~ Selected number in
Sense-up
1/30
1/33000 ~ 1/30
1/50
1/33000 ~ 1/50
1/60
1/33000 ~ 1/60
1/100
1/33000 ~ 1/100
1/125
1/33000 ~ 1/125
1/250
1/33000 ~ 1/250
1/500
1/33000 ~ 1/500
1/1000
1/33000 ~ 1/1000
1/33000 1/33000
* Sense-up options: 1/30, 1/15, 1/10
