Eaton ATC-300+ O & M Manual Download Page 10

For more information visit: www.chfire.com

IM05805022K

Instruction Booklet

Page

 

10

Effective:  January 2012

ATC-300+ Automatic 

Transfer Switch Controller

2.4  Specification Summary

Table 1.  ATC-300+ Controller Specifications

Input Control Voltage

65 to 145 Vac  50/60 Hz

Voltage Measurements of

Source 1 VAB

 Source 2 VAB

Source 1 VBC

 Source 2 VBC

Source 1 VCA

 Source 2 VCA

Voltage Measurement Range

0 to 790 Vac RMS (50/60 Hz)

Voltage Measurement Accuracy

± 1% of Full Scale

Frequency Measurements of

Source 1 and Source 2

Frequency Measurement Range

40 Hz to 70 Hz

Frequency Measurement Accuracy

± 0.3 Hz Over the Measurement Range

Undervoltage Dropout Range:

Breaker/Switch Style ATS

50 to 97% of the Nominal System Voltage

Undervoltage Pickup Range:

Breaker/Switch Style ATS

(D2%) to 99% of the Nominal System Voltage

Overvoltage Dropout Range:

Breaker/Switch Style ATS

105 to 120% of the Nominal System Voltage

Overvoltage Pickup Range:

Breaker/Switch Style ATS

103% to (Dropout -2%) of the Nominal System Voltage

Underfrequency Dropout Range:

Breaker/Switch Style ATS

90 to 97% of the Nominal System Frequency

Underfrequency Pickup Range:

Breaker/Switch Style ATS

(D1Hz) to 99% of the Nominal System Frequency

Overfrequency Dropout Range:

Breaker/Switch Style ATS

103 to 110% of the Nominal System Frequency

Overfrequency Pickup Range:

Breaker/Switch Style ATS

101% to (Dropout -1Hz) of the Nominal System Frequency

Operating Temperature Range

-20 to +70°C (-4 to +158°F)

Storage Temperature Range

-30 to +85°C (-22 to +185°F)

Operating Humidity

0 to 95% Relative Humidity (Non-condensing)

Operating Environment

Resistant to Ammonia, Methane, Nitrogen, Hydrogen, and Hydrocarbons

Generator Start Relay

5 A, 1/6 HP @ 250 Vac

5 A @ 30 Vdc with a 150 W Maximum Load

K1, K2, Pretransfer, Alarm Relays

K3, K4

10 A, 1-3 HP @ 250 Vac

10 A @ 30 Vdc

Applicable Testing 

UL Recognized Component

Meets UL 1008

Meets Intent of UL 991,

Meets IEC 1000-4-2, 1000-4-3, 1000-4-4, 1000-4-5, 1000-4-6, 1000-4-11

Meets CISPR 11, Class A

Complies with FCC Part 15, Class A

Enclosure Compatibility 

NEMA 1, NEMA 3R, NEMA 12 and NEMA 4X

UV Resistant ATC-300+ Faceplate

Summary of Contents for ATC-300+









































Reviews: