background image

Instructional Booklet

Page

12

Effective: July 2010

ATC-100 Contactor Based Transfer Switch

For more information visit: www.eaton.com

IB01602017E

Power cables are to be connected to solderless screw type lugs 

located on the ATS switching devices.  Refer to the separate Cus-

tomer Wiring Booklet supplied with the ATS equipment for power 

termination.  Verify that the lugs supplied will accommodate the 

power cables being used.  Also verify that the cables comply with 

local electrical codes.  Standard ATS equipment, as supplied from 

the factory, will accommodate the wire sizes shown in Table 4.

Carefully strip the insulation from the power cables to avoid nick-

ing or ringing of the conductor strands.  Prepare the stripped con-

ductor termination end by cleaning it with a wire brush.  If 

aluminum conductors are used, apply an appropriate joint com-

pound to the clean conductor surface area.

Tighten the cable lugs to the torque identified on the label affixed 

to the door of the unit.

4.5  Wiring

Power sources, load conductors, and control wiring should be 

connected to locations as indicated in the Customer Wiring Book-

let supplied with the ATS equipment.

Once the ATS equipment has been installed and wired, perform 

the initial mechanical and electrical procedures as outlined in Sec-

tion 6 to verify that the equipment is installed and operating prop-

erly.

Table 4. Transfer Switch Equipment Wire Size

 

WARNING

IMPROPER POWER CABLE CONNECTIONS CAN CAUSE EXCESSIVE 

HEAT AND SUBSEQUENT EQUIPMENT FAILURE.

 

 

WARNING

POWER CONDUCTORS AND CONTROL WIRING MAY HAVE VOLT-

AGE PRESENT THAT CAN CAUSE SEVERE PERSONAL INJURY OR 

DEATH.  DEENERGIZE ALL POWER OR CONTROL CIRCUIT CONDUC-

TORS BEFORE BEGINNING TO PERFORM ANY WIRING ACTIVITY TO 

OR WITHIN THE ATS EQUIPMENT.

CAUTION

ENSURE THE ATC-100 VOLTAGE IS SET CORRECTLY.  IT SHOULD 

BE THE SAME AS THE UTILITY AND THE GENERATOR LINE VOLT-

AGES.  OPERATING THE EQUIPMENT ON IMPROPER VOLTAGE CAN 

CAUSE EQUIPMENT DAMAGE.

TRANSFER SWITCH AMPERE RATING

WIRE SIZE RANGES

NUMBER OF CABLES PER PHASE

TERMINAL TEMPERATURE RATING °C (°F)

30-100

#14-3/0

1

75 (167)

150

#6-300KCMIL

1

75 (167)

225-300

#3-350KCMIL

1

75 (167)

400

#3-350KCMIL

2

75 (167)

600

#1-500KCMIL

2

75 (167)

800-1200

#3/0-500KCMIL

4

75 (167)

Summary of Contents for ATC-100

































Reviews: