2
6.
Connect wiring adaptor to house-side adaptor
(D) to make electrical connection (Fig. 4).
7.
Thread wiring through mounting bracket into the
junction box while positioning the fixture onto the
mounting bracket receivers (Fig. 4).
8.
Using a screwdriver, screw the mounting screws (E)
into the mounting bracket in both places until tight,
and make any necessary adjustments to the fixture
orientation. Insert the decorative screw cover caps
(F) into the screw holes on the faceplate for a
finished appearance (Fig. 4).
9.
Caulk around the base of the fixture, leaving the
drain slots open.
10.
Turn on power at main fuse/breaker box.
OPERATING YOUR FIXTURE
(MOTION ACTIVATED MODELS)
1.
Rotate duration knob on back of the sensor to
“TEST” (Fig. 6).
2.
Turn on the power to fixture. Allow fixture to warm
up approximately 40 seconds before testing. (Lights
will come on during warm-up period).
3.
Walk across the detection zone to verify the motion
sensor function. Adjust sensitivity knob (Fig. 8)
to set your desired range. Lights will turn off 4
seconds after all motion stops.
NOTE:
For maximum range performance, allow fixture
to operate in any mode (with power to the unit) for at
least 48 hours.
4.
To set the ON time, rotate Duration knob to point to
the desired time setting (up to 12 minutes) (Fig. 7).
5.
To temporarily bypass motion activation and
keep the fixture on for 6 hours, turn the power
OFF and ON twice within 3 seconds.
ENERGY STAR
®
SELECTING YOUR DESIRED FEATURE (MOTION ACTIVATED MODELS)
TROUBLESHOOTING (MOTION ACTIVATED MODELS)
TROUBLESHOOTING (DUSK TO DAWN MODELS)
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
TURN OFF POWER BEFORE CONTINUING.
Wiring to the unit is loose.
• Confirm wiring is properly secured.
Light does not
come ON.
ENERGY STAR
®
is sponsored by the
U.S. Environmental Protection Agency
& U.S. Department of Energy.
Visit www.energystar.gov to learn more.
Mode of
Knob
How to Set
Operation Adjustment
Power Switch
Auto Setting (motion activated)
Lights should turn ON with
motion only at night and should
turn OFF according to the
Duration setting.
Knob arrow points to
desired time setting.
Turn the power
to the fixture ON.
Problem
Cause / Solution
Light does not
come ON with
motion at night.
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring; reconnect if necessary.
Light
comes ON
for no apparent
reason at night.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard to prevent sensor from
detecting motion. If the light stays off, something in the detection
zone is triggering the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
• Reposition the fixture.
Light stays ON at
night and does
not turn OFF.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition the fixture.
Unit is in override mode (if there is no motion).
• Turn the light switch to the OFF position for 40 seconds, and
then turn back to the ON position. This will send the unit back
into the “Auto” mode.
Light is ON
during the day.
The controls on the back of the motion sensor are in “TEST” mode.
• Change dial setting (not “TEST” mode).
The motion detector is shadowed.
• Reposition fixture.
Cannot activate
dusk to dawn
mode at night
(override).
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Relocate or reposition the unit away from the light.
Not enough time is allowed to enter the dusk to dawn mode.
• Turn power OFF and ON twice within 3 seconds.
There is more than one fixture on an indoor wall switch.
• If possible put each fixture on a separate switch.
6
7
8
Light does not
come ON.
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
Fixture is sensing daylight.
• Cover light sensor. Unit will switch ON immediately.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Confirm wiring is properly secured.
* If light still does not come on after checking wiring
connections, contact Customer Service.
5
E
A
F
4
D
Sensitivity Duration
Knob rotated to RUN position
Knob rotated to TEST mode
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
Turn the power
to the fixture ON.
TEST
Return to Auto Setting
(motion activated)
From any of the above settings
Knob arrow points to
desired time setting.
Turn the power OFF
for at least 40 seconds
and then back ON.
Dusk to Dawn Setting
(activated only at night)
Lights should turn ON for 6 hours
at dusk and then reset to
the Auto Setting.
Knob arrow points to
desired time setting.
Turn the power
OFF and ON twice
within 3 seconds.
Problem
Cause / Solution
