manualshive.com logo in svg

Eaton 9PX3K3U, Installation And User Manual

Share
Download
Eaton 9PX3K3U Installation And User Manual Download Page 17

Page 17

9PX3K3U_EN

ENGLISH

3. Installation

3.3   Checking the accessory kit

•  Verify that the following additional items are included with the UPS:

1

4

2

10

8

7

9

5

6

6

3

11

1

  (2)Tower stands

2

  Rack kit for 19-inch enclosures

3

   Cable gland for Output connection 

Additional cable gland for Input 

4

  Network card-MS communication card

5

  RS232 communication cable

6

  USB communication cable

7

  User manual

8

  Safety instructions

9

  Warranty sheet

10

  Software CD-ROM

11

 Screwdriver

•  If you ordered an optional Extended Battery Module (EBM), verify that the following additional items are 

included with the EBM:

3

4

2

1

1

   Battery power cable, attached with battery 

detection cable

2

   Stabilizer bracket (4 screws included)

3

   Rack kit for 19-inch enclosures

4

   EBM Installation manual

Discard the EBM user’s guide if you are installing the EBM with a new UPS at the same time. 
Use the UPS user’s guide to install both the UPS and the EBM.

If you ordered other UPS accessories, refer to specific user manuals to check the packing 
contents.

Summary of Contents for 9PX3K3U















































Reviews:

No comments

Brands by name

Popular brands

Load more brands