background image

19

Instruction Book    

IB182217EN   October 2018   www.eaton.com

50 / 75 / 150 DHP [Cable or Hard Bus Application]

Ground and Test Device

4.9 UNIVERSAL 1200A/2000A G&T CONFIGURATION 

(OPTIONAL)

A special design of the DHP Ground and Test Device (G&T) allows 

the separate grounding of both 1200A and 2000A circuit breaker 

cubicles.  Since the device can be inserted into either cubicle design, 

the finger clusters and the G&T code plate must be matched to the 

ampere rating of the cell stabs.

m

 DANGER

FAILURE TO CORRECTLY MATCH THE FINGER CLUSTER RATINGS AND 

G&T CODE PLATES TO THE CELL STAB AMPERE RATING CAN RESULT IN 

DEATH, SERIOUS PERSONNEL INJURY, AND / OR PROPERTY DAMAGE.

Step 1 - Determine the ampere rating of the cell structure that is to 

be grounded or tested with the G&T device.
Step 2 - Verify that the code plate is installed properly by referring 

to Section 4.5 in this instruction book based on the ampere rating.  

If the code plate is incorrectly mounted, remove it and remount to 

match the proper ampere rating.
Step 3 - The correct finger cluster (1200A or 2000A) must match 

the cell stab ampere rating prior to inserting the G&T device.  If the 

incorrect finger cluster is mounted on the G&T device, remove it and 

install the proper finger cluster.

4.7.1 Changing 1200A Finger Clusters to 2000A

The 1200A DHP finger cluster is easily changed by removing the 

5/16” hex head bolt, lock washer, and large retaining washer. 

(Figure 4.6 & 4.7) Retain the hex head bolt and lock washer for 

re-installation or for mounting a 2000A universal G&T finger cluster.

fingers (Figure 4.10). The finger cluster should be re-waxed each 

time a finger cluster is changed or approximately every 50 insertions 

and removals.  The wax will not form a build-up and will not attract 

dirt and contaminants if properly applied.

Figure 4.6. 1200A Finger Cluster Removal

Figure 4.7. Finger Cluster Hardware

Pull the finger cluster assembly off the G&T primary conductor.  

Repeat the process for all finger clusters.
Select a 2000A universal G&T finger cluster (Figure 4.8).
Apply a thin film of wax (Johnson’s Paste Wax-available from many 

retailers-used for furniture) to the outer surface of the primary 

conductors (Figure 4.9) and to the inside contact surfaces of the 

Figure 4.8. 2000A Universal G&T Finger Cluster

Figure 4.9. Waxing Primary Conductors

Figure 4.10. Waxing 2000A Universal G&T Finger Cluster

Summary of Contents for 150 DHP



























Reviews: