background image

易仕韦尔

EASYWELL

6

Operation as following:

a) Cut off the power, drain the water from the tank and dry the water on the

surface of the atomizer.

b) Unscrew the ring with the lock piece, remove the old ceramic disc, and keep

the atomizer chamber clean.

c) When install the new ceramic disc front face up, and reverse side back down.

Then tighten the pressure ring.

Special tips:

When the water level 0.1-0.5cm higher than the atomizer’s sensor,

the atomizer in the best working status. If the water level is too high or too low,
the fog outlet capacity will be affected.

Remark

To avoid the float displaced in transportation

please adjust the water

level when the first time using.

5. Regular failure and failure elimination

Fault symptom

Reason

Remove method

Not working

a) No Power
b) Fuse blown
c) The power switch is not on
d) Humidity over the settled

a) Check the circuit, power

restoration

b) Replace the fuse
c) Turn on the power switch

No water adding

a) No water in the water supply

pipe

b) The water float is blocked
c) The water supply pressure is

not enough

a) Check the water supply

circuit

b) Remove the foreign matter in

the float

c) The pressure must reach

5KG.

Don’t stop when
adding water

a) The water float is displaced
b) There is foreign matter in the

a) Adjust it to the correct

position

Summary of Contents for EW-020TH










Reviews: