background image

12

RevitaLife    |    Installation Manual & Owner’s Guide

Limited Warranty

EasyWater, Inc., Fishers, IN warrants this EasyWater RevitaLife (referred to as System) as stated 
herein:

From the date of installation, within the warranty period described below, we will repair or replace 
any part which we find defective because of faulty materials or workmanship.  You pay only freight to 
our factory and local labor charges.

 

-

One year on complete unit excluding cartridges and membranes

Damage to any part of System because of misuse, misapplication, neglect, alteration, accident, 
installation or operation contrary to printed instructions, or damage caused by an act of terrorism 
or any unusual force of nature such as, but not limited to, freezing, flood, hurricane, tornado or 
earthquake is not covered by this warranty.  In all cases, regular parts and service charges will 
apply.

We assume no warranty liability in connection with this System other than specified herein.  This 
warranty is in lieu of all other warranties, express or implied, including warranties of fitness for a 
particular purpose.  We do not authorize any person or representative to assume for us any other 
obligations on the sale of this filter.

Should a defect or malfunction occur, EasyWater, Inc., at (888) 766-7258 or via email at 
[email protected].  We will repair or replace the part at no cost if our repair 
department determines it to be defective under the terms of the warranty.

Feed water quality must meet the requirements for this system on an ongoing basis in order for 
this warranty to be valid.

This warranty is valid for the original purchaser only and gives you specific legal rights.  You may 
have other rights which vary from state to state.

FREIJE Treatment Systems, Inc.
9715 Kincaid Drive Suite 1100 Fishers, IN 46140
(888) 766-7258 

Lit No. RLISMOG021813

Summary of Contents for RevitaLife














Reviews: