9
2
Setting the Features
Using the Voltometer
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Volts”. Turn
the voltometer on by pressing the Left Rear Inflate button (F).
Adjusting the Brightness
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Bright”.
Adjust the brightness by pressing the Left Rear Inflate button (F) to increase the brightness and the Right
Rear Deflate button to decrease the brightness.
Using the Sequence Feature
The sequence feature allows your air suspension system to inflate your front air springs before
inflating your rear springs while achieving ride height.
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Seq.”.
Using Leak Detection
The leak detection feature will detect a leak in your air system after the manifold while auto ride
height is enabled.
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Leak”. Turn
the leak detection on by pressing the Left Rear Inflate button (F).
Tank Pressure
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Tank”. Turn
the tank pressure display on by pressing the Left Rear Inflate button (F).
Auto Ride Height on Start
Auto Ride Height will allow your air suspension to automatically achieve ride height when you turn
the key in your vehicle.
1. Press and hold the Ride Height button (B) for greater than 3 seconds until “Edit Options” appears.
2. Press the Right Front Inflate button (J) and scroll through the Edit Options menu until you see “Auto”. Turn
the Auto Ride Height feature on by pressing the Left Rear Inflate button (F).
Setting the Features (Continued)
Operational Instructions
Operational Instructions
Three Basic Operation Modes:
Settings:
Manual-Mode
Auto-Mode
Option-Mode
The system displays the actual airbag pressures, and the user controls the pressure manually.
The system displays the pressure settings and automatically maintains the prescribed airbag
pressures.
The user can examine and change all option settings.
The system keeps the user’s option settings in non-volatile memory so that they will be maintained each time the
system is powered up. On power-up, the options settings are read and acted on appropriately.
Ride Ht
Auto
Leak
The system will immediately restore the airbag pressures to the saved setting values on power-up.
When ride-height is selected (either through “Ride Ht” option setting or user selection during
operation), the system will automatically maintain the airbag pressure at the current settings.
The system will display detected leaks in any of the airbag circuits. A leak is shown by the letter
“L” next to the pressure reading.
Volts
Bright
The display will show the system voltage. If both “Volts” and “Tank” are enabled, the display
will alternate between them every 20 seconds.
The display will show the current tank pressure. If both “Volts” and “Tank” are enabled, the
display will alternate between them every 20 seconds.
Controls the display intensity. If the display intensity is changed while it is dimmed automatically by
the vehicle lights connection, it will remain at the selected brightness until the next time the vehicle
lights are turned on.
Tank
The system will perform pressure regulation on the airbags sequentially (left front, right front,
left rear, right rear). If not enabled, the system will simultaneously adjust all airbag pressures.
Seq
To use the TUNE function, the tune option must be set to ON and it must be displayed when
the ride height button is used to exit option-mode. The TUNE function will test the response of
the system by exercising the airbags individually. The results are stored by the system for use
in accurately controlling airbag pressures. The TUNE function must only be accomplished in a
stationary vehicle on level ground.
Tune
