background image

3

Congratulations on your new Easyrig Vario 5!

 

The Easyrig vario 5 has an adjustable weight range from 5-17kg (11-38 lbs). 

By turning the adjustment screw located on the back, you can easily 

change the tension / power of the line.

The Easyrig vario 5 gives you the same advantages as our other Easyrig 

models with the added benefit of being able to adjust the line tension to 

adapt to many different cameras and configurations. The Easyrig vario 5 

still delivers the same steady hand held shots while relieving you back, 

neck and shoulders. The load is redistributed to the hips allowing you to 

shoot hand held in comfort for hours. 

The Easyrig vario 5 will be your best tool when it comes to hand-held 

shooting for Movies, Commercials, Television and any other situation 

where stability and freedom of movement are crucial.

The Easyrig vario 5 is manufactured in Sweden and is built to the highest 

standards. The Easyrig vario 5 is ergonomically designed and field tested 

to achieve maximum results.

To get the most out of your Easyrig vario 5, please read this user manual 

carefully.

Thank you for your investment in the Easyrig vario 5.

Good Luck!

 

Johan Hellsten

Cameraman and 

Inventer of Easyrig

Summary of Contents for vario 5













Reviews: