background image

 
 
 
 
 

 

Step 6

 - Open the door till fully ajar, press 

Enter button

.  The open position LEDS will then flash 

green. 
 

Step 7

 - Release door. 

 

Step 8

 - With door in the closed position, press 

Enter button

.  A second non-labelled LED will flash 

green then stop. 
 

Step 9

 - Stand clear from the door.  The door will then quickly open halfway and then close. 

 

Step 10

 - Press and hold 

Enter button

 until DS9 LED flashes to confirm you have exited the 

programming. 

 
 

Variable Open and Close Options 
 

To enter programming mode: 
 

Step 1

 - Press and hold 

Enter

 and 

Select buttons

 for 3 seconds. 4 green LEDS will flash. 

 

Step 2

 - Wait for the 4 green LEDS to stop flashing, and 1 CLS green LED to light. 

 

Step 3

 - Press and release 

Select button

.  The green CLS LED will go off, and the green OP LED 

position light will come on.  
 

Step 4

 - Press 

Select button

 until desired operating mode is highlighted by green LED 

 

Step 5

 - Press 

Enter button

 once. 

 

Step 6

 - Press 

Enter

 

button

 again and hold for 3 seconds. 

 
You will now have exited the programming.  

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for PUSH


















Reviews: