background image

 

 

Step  2:  Click  the  terminal  of  the  ward,  then  the  location  of  the  ward  will  be 
displayed on the map. 
 

2. Setup of Centre Number 

Set  the  centre  number  by  SMS  through  the  mobile  phone,  after  the  setup  is 
successful,  then  the  mobile  phone  that  sending  the  SMS  will  receive  the 
“&710&successful setting&&” response message from the terminal.   
Command format: #710# center number # user password ## 

 

For example: #710#134xxxxxxxx#0000## 
Note: All alarming information thereafter including SOS, low power, electronic 
fence, etc will be returned to that number. 
 

3. Bi-directional Call Function 

Incoming  calls  can  be  rejected  by  pressing  upper  left  button  or  received  by 
pressing middle right button. 
Send the command in form of SMS to the terminal via mobile phone. After the 
setup  is  successful,  the  mobile  phone  will  receive  the 

“&711&successful 

setting&&” response message from the terminal. 
Setup format: #711# Call1# Call2 # Call3 # 0000## 
incoming call interface and call duration interface 
Notes: After the setup is  successful, press the upper right button for a while, 
then  the  terminal  will  automatically  dial  the  first  phone  number.  Press  the 
bottom right button, then the terminal will automatically dial the second phone 
number.   
 

4. Adjust Receiver Volume 

While making phone calls, the user could press upper or bottom right button to 
adjust receiver volume. 
 

5. SOS Function   

If  a  ward  number  (predetermined  number  in  item3)  is  set,  when  the  ward 
encounters  emergency  and  presses  the  SOS  button,  the  terminal  will  send 
alarming information to the center number and dial the three ward numbers in 
turn. 
SOS SMS format: IMEI number: SOS (information about latitude and longitude 
or base station) 
Example: 356823031017473:SOS

11354.6397,E,2232.6283,N

 

or 356823031017473:SOS

26280E77

 

Remarks: when interface in picture 5  appears on the phone, the terminal will 
skip to standby mode automatically; sound and interface during the dialing will 
be completely shielded. 

 
6. Monitoring Function 

The guardian may send SMS 555 plus password to the terminal of the ward, 

Summary of Contents for Gps watch









Reviews: