background image

12

 

Eastwood Technical Assistance: 800.343.9353  >>  [email protected]

FIG. 9

FIG. 9

FIG. 10

FIG. 10

THREADING WELDING WIRE THROUGH THE 

DRIVE MOTOR TO THE WELDING GUN

This Welder uses wire sizes ranging from 0.023” to 0.030” (0.6mm to 0.8mm).  
To safely and correctly install the welding wire; follow the procedure in the  
sequence outlined below:

1. 

Turn the Power Switch on the Upper rear Panel to the “OFF” position and unplug 
the Welder from the power supply.

2. 

Using the included Contact Tip Wrench 

[N] 

Remove the Contact tip and Nozzle 

from the end of the MIG Gun.

3. 

Make sure that the drive roller is installed in the proper position in accordance 
with the wire size being used. As Described in “POSITIONING DRIVE ROLLER  
for WIRE SIZE” section of these instructions.

4. 

Flip the Wire Tensioner upward, pivot it up and out of the way then pivot the  
Tension Arm out away from the Drive Roller 

(FIG 9)

5. 

Pull out the welding wire from the wire spool carefully. 

IMPORTANT NOTE:

 DO NOT let go of the wire or the entire spool could unravel.

6. 

Cut off the small piece of the curved segment at the front of welding wire and 
straighten the welding wire approximately 3.0” long.

7. 

Thread the welding wire feeding from the topside of the spool and forward 
through the Guide Tube then over the wire Drive Roller and into the Wire Feed 
Hole 

(FIG 10)

.

8. 

Replace the Tension Arm and re-latch the Wire Tensioner back into place  

(FIG 11)

.

9. 

Connect the Welder to a power supply and Turn the ON/OFF Switch at the upper 
rear panel to the “ON” position. Set the Wire Speed Control to about 212 IPM.

10. 

With the gun pointed away from yourself and others, depress the trigger to begin 
feeding wire. When not welding, the welder will assume wire is being fed and the 
wire speed potentiometer will be disabled. The welder will automatically start a 
slow feed, and after a few seconds of the trigger being held, it will switch to a 
fast feed to get the wire completely through the torch faster.  

NOTE:

 The Wire Tensioner may need to be set. To do so:

  -  Watch the drive roller to see if any slipping is occurring between the roller  

  and the wire. If so; turn the machine off, unplug it and tighten the Wire  
  Tensioner 1⁄4 turn and test again.

  -  Repeat the above step until wire is feeding smoothly with no binding  

  or slippage.

Once the wire exits the end of the MIG Gun, reinstall the contact tip and nozzle.  
Cut the wire about 1/4” from the end of the contact tip.

FIG. 11

FIG. 11

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH! 

  This procedure requires that the Welder power be switched ON. 

DO NOT make contact with the wire when the MIG Gun Trigger  
is depressed.

Summary of Contents for MIG 90

























Reviews: