2
Eastwood Technical Assistance: 800.343.9353 >> [email protected]
STATEMENT OF LIMITED WARRANTY
The Eastwood Company (hereinafter “Eastwood”) warrants to the end user (purchaser) of all new welding and cutting equipment (collectively called the “products”) that it will
be free of defects in workmanship and material. This warranty is void if the equipment has been subjected to improper installation, improper care or abnormal operations.
WARRANTY PERIOD:
All warranty periods begin on the date of purchase from Eastwood. Warranty Periods are listed below, along with the products covered during those warranty periods:
3 Year Warranty on Material, Workmanship, and Defects:
• Eastwood MIG 135 Welder
Items not covered under this warranty: Contact tips, nozzles, wire, and ground clamp and cable.
All other components are covered by the warranty and will be repaired or replaced at the discretion of Eastwood.
2 Years:
• All Welding Helmets.
CONDITIONS OF WARRANTY TO OBTAIN WARRANTY COVERAGE:
Purchaser must first contact Eastwood at 1-800-345-1178 for an RMA# before Eastwood will accept any welder returns.
Final determination of warranty on welding and cutting equipment will be made by Eastwood.
WARRANTY REPAIR:
If Eastwood confirms the existence of a defect covered under this warranty plan, Eastwood will determine whether repair or replacement is the most suitable option
to rectify the defect. At Eastwood’s request, the purchaser must return, to Eastwood, any products claimed defective under Eastwood’s warranty.
FREIGHT COSTS:
The purchaser is responsible for shipment to and from Eastwood.
WARRANTY LIMITATIONS:
EASTWOOD WILL NOT ACCEPT RESPONSIBILITY OR LIABILITY FOR REPAIRS UNLESS MADE BY EASTWOOD. EASTWOOD’S LIABILITY UNDER THIS WARRANTY SHALL NOT
EXCEED THE COST OF CORRECTING THE DEFECT OF THE EASTWOOD PRODUCT. EASTWOOD WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (SUCH
AS LOSS OF BUSINESS, ETC.) CAUSED BY THE DEFECT OR THE TIME INVOLVED TO CORRECT THE DEFECT. THIS WRITTEN WARRANTY IS THE ONLY EXPRESS WARRANTY
PROVIDED BY EASTWOOD WITH RESPECT TO ITS PRODUCTS. WARRANTIES IMPLIED BY LAW SUCH AS THE WARRANTY OF MERCHANTABILITY ARE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY FOR THE EQUIPMENT INVOLVED. THIS WARRANTY GIVES THE PURCHASER SPECIFIC LEGAL RIGHTS.
THE PURCHASER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
SPECIFICATIONS
Output
Amperage
Range
Maximum
Output
No Load
Voltage
Maximum
Input
Amperage
Input
Voltage
Rated
Duty
Cycle
Wire
Feed
Rate
Welding
Wire Spool
Sizes
Weight Overall
Dimensions
25-135 A
28 V DC
20 Amp
120 VAC
60 Hz
20%
@ 90 A
40-
450 IPM
4-8"
56 Lbs.
[25kg]
16.5" L [408mm] x 9.6" W [244mm] x 14.5" H [367mm]
Wire Type
Solid
Stainless
Flux Cored
Diameter
0.023-0.030"
[0.6-0.8mm]
0.023-0.030”
[0.6-0.8mm]
0.030-0.035”
[0.8-0.9mm]
UNPACKING
When unpacking your Eastwood MIG135, check to make sure all of the parts listed below are included:
(1)
MIG135 Welder
(1)
MIG Gun Cable Assembly (9 ft.)
(1)
Ground Cable Assembly (9 ft.)
(1)
Gas Flow Regulator
(1)
Gas Hose
(1)
Hand Held Shield
(1)
Wire Brush
(1)
2lb Spool of 0.023in (0.6mm) Solid Wire
(2)
Contact Tips
(1)
Contact Tip Wrench
(1)
Instructions
