4
Eastwood Technical Assistance: 800.544.5118 >> [email protected]
To order parts and supplies: 800.345.1178 >> eastwood.com
5
UNIT SELECTION
1.
Once the Peak / Track mode has been set, the wrench switches to the setting of
“UNIT SELECTION”.
2.
is shown on screen, select the units between lb/ft, lb/in, kg.m, N.m by
pressing button.
3.
Press button to confi rm the unit selection. The wrench will switch to Auto Power Off
Settings when the button is pressed.
NOTE:
If there is no button activity for 3 seconds, the wrench will retain the last selection of Units,
and return to measurement mode.
AUTO POWER-OFF SETTINGS
The torque wrench will be turned off automatically without any button activity over a selectable
period. Changing the auto –off setting as follows:
1.
Once the unit is selected, the default
Auto-Off
time:
5 (5 minutes)
will be shown on screen.
2.
Wait for 2 seconds without touching any buttons, or press button to retain the default
setting.
3.
Changing the wrench
Auto-off
time by pressing button. Select the shut-off time
between
5
minutes,
15
minutes or
“OFF”
to turn off the Auto-off function.
4.
Press button to confi rm the selection. The wrench returns to measurement mode when
the button is pressed.
NOTE:
If there is no button activity for 3 seconds, the wrench will retain the last selection of Auto
Power Off, and return to measurement mode.
PROGRAMMING THE TORQUE AND ANGLE
The wrench has
5 sets
of memory storage for pre-setting the target Torque and Angle.
TARGET TORQUE SETTING
1.
Press button to turn the wrench on.
2.
Press button to select the memory storage number between
M1~M5
.
3.
Once the memory number is chosen, access the target Torque/ Angle programming
by pressing and holding button for 5~10 seconds.
4.
Release button when is shown on screen, and the last saved torque is dis-
played. The fi rst digit of this value (“0000” ) is fl ashing. Press button to zero the last
saved value. Or by repeatedly pressing button, the value of the fl ashing digit is gradually
increased. When the desired value is reached, press button to skip to the next decimal
place. Repeat this process for all numeric places. (ones, tens, hundreds etc.) Example: A cor-
rect setting for
75 lb/ft
will read
075.0
in the display.
5.
When the required torque level is set, press to save the value.
Ft/lb
SET
TARGET ANGLE SETTING
1.
The display skips to Angle setting automatically once the target torque is set, and displays the
last saved angle value. The fi rst digit of this value (“0000”) is fl ashing.
2.
Press the button to zero the last saved value. Or by repeatedly pressing button,
the value of the fl ashing angle digit is gradually increased. When the desired value for this digit
was achieved, press button to skip to the next digit. Repeat this process for all numeric
places in the angle value.
3.
When the required angle is set, press to save the value.
NOTE:
If there is no button activity for 5 seconds, the wrench will retain the last selection of
Angle Setting and automatically switch to Measurement Mode.
TURNING THE DISPLAY ILLUMINATION ON / OFF
1.
The display illumination can be turned on prior to or after programming the torque.
2.
In order to do this, press and release the button.
OPERATING THE TORQUE WRENCH
1.
Select the socket required for your work.
2.
Attach the socket fi rmly to the square drive of the torque wrench, it will be held in place by the
ball stop of the square drive.
3.
If possible, do not use any extensions because they may distort the torque applied to a bolt.
APPLYING PROGRAMMED TORQUE
1.
Program the value necessary following the instructions in the
Target Torque Setting
section.
2.
Place the torque wrench on the fastener. Grip the torque wrench and PULL on the wrench with
a slow, easy movement. Avoid jerky movements.
3.
With the target torque pre-set, the target value is indicated on the screen.
4.
The LED will show
GREEN
when you are under 50% of the programmed torque value.
5.
When approaching the target torque value,, the LED turns to
YELLOW
.
6.
When you approach the programmed torque value, the buzzer will sound.
7.
When you are
within 2%
of the programmed torque value, the
RED
LED will illuminate.
Once the torque is reached, the buzzer will emit quicker sound sequence.
8.
If
you
exceed the programmed torque by 2%
, the buzzer will emit a continuous tone and the
LED will turn
GREEN
.
ATTENTION: When you hear the continuous tone and the RED LED illuminates, stop pulling
immediately or target torque will be exceeded.
NOTE:
If there is no button activity for 5 seconds, the wrench will retain the last selection of torque
and automatically switch back to Angle Programming.
NOTE:
“Erro” (for ERROR will show on the display when the pre-set torque value exceeds 100% of the
maximum torque value. After 1 second, the display returns to torque Measurement Mode.
NOTE:
After pressing the “+” button to access the torque setting mode, without any activity after
6 seconds, the display will return to Measurement Mode.
