5
Form CR-50-0433
Familiarization
Control Box
1.
Main Power
: Activates power to all circuits. L CD display
is on when in ON position.
2.
Clamp:
Press to open/close material Clamp.
3. Start Cut:
Press to begin cut process. This can also be
achieved by pressing the remote start button.
4. Return/Abort:
Press to stop the blade and Return
carriage to home position/Press to stop the blade and
Abort the automatic cut process.
5. Digital Display:
Displays ply status, command status,
or display for programming.
6. Command Keys/Keypad:
Clear 000(0):
Press to clear ply counter to 000 (zero key)
Flaw Cut(1):
Press to cycle the Blue Jay Cutter and lift
without adding the ply count. (One Key)
Sharp On(2):
Press to start sharpen cycle. The cutter
will travel across the track with the blade spinning.
Sharpen the blade by pressing the sharpen lever with a
constant pressure. Hold for 10 seconds. Press the
Sharpen Off key to exit and return the cutter. (Two Key)
Auto Lift(3):
Press to change the auto lift status to Auto
Lift On or Auto Lift Off. Set The Auto Lift Time by pressing
+ / - keys. This will adjust the time the track lifts after a cut
cycle. (1-4 second range) Press the return key to exit Lift
Time Program. (Three Key).
Lift Up/+(4):
Press to raise the track to the up position.
When in program mode press to increase number
display by one. (Four Key)
Preset Count(5):
Press to enter preset counter mode.
Use the number keys to set number of plies to cut. When
this number of cycles has lapsed, the machine will stop,
the display will flash and the beeper will sound. Press the
Return key to exit. The "000" value will continuously
count cycles without stopping or sounding the alarm.
(Five Key)
Count Adjust(6):
Press to adjust ply count. Use the +(4)
key or -(9) key to adjust ply count. Press the Return key
to exit. (Six Key)
Sharp Off(7):
Press to exit sharpen mode. The Blue Jay
Cutter will return to home position. (Seven Key)
***When machine is in idle mode, press Sharp Off key to set
the number of cut cycles between blade sharpening.
Use the +(4) key or -(9) key to adjust number of cycles.
Press the Return key to exit. When this number of cycles
has lapsed, the machine will stop, the display will flash
and the beeper will sound. The "000" value will disable
the sharpener reminder alarm.
Clamp Open,Close(8):
Press to open or close the Blue
Jay Material Clamp. (Eight Key)
Lift Down/-(9):
Press to lower the track to the down
position. When in program mode press to decrease
number display by one. (Nine Key)
7. Beeper:
Beeps when number of plies have been
reached. Clear Counter to stop sound.
8. Main Outlet:
Connects main wiring harness to main lift
module.
9. Power Clamp Outlet:
Connect Power Clamp Harness
here.
10.Pull-off Outlet:
Connects Harness to mating outlet on
pull off device (optional).
11.Remote Outlet:
Connect remote control Harness here
(optional).
Summary of Contents for BLUE JAY-5H
