background image

 

Package

 

Overview

 

Installation

1

2

3

4

2

1

3

Thank you for purchasing our product. There may be several 

technically incorrect places or printing errors in this manual. 

The updates will be added into the new version of this manual. 

We will readily improve or update the products or procedures 

described in the manual. The content is subject to change 

without notice.

Warning

 

and

 

Caution

 

If the product does not work properly, please contact your dealer 

or the nearest service center. Never attempt to disassemble the 

camera yourself. (We shall not be responsible for any problems 

caused by unauthorized repair or maintenance.)

 

Keep away from liquid while in use.

 

In the use of the product, you must be strict compliance with the 

electrical safety regulations of the nation and region. When the product 

is mounted on wall or ceiling, the device shall be firmly fixed.

 

Do

 

not

 

use

 

camera

 

beyond

 

specified

 

voltage

 

range

.

■ 

Do not drop the camera or subject it to physical shock.

■ 

 Avoid touching the camera lens.

■ 

If cleaning is necessary, please use clean cloth to wipe it gently.

 If the device will not be used for a long time, please cover the lens

 cap to protect the device from dirt.

■ 

Do not aim the camera at the sun or extra bright place. 

■ 

Do not place the camera in extremely hot, cold (the operating

 temperature shall be -20˚C~50˚C), dusty or damp locations, and do 

not expose it to high electromagnetism radiation.

■ 

To avoid heat accumulation, good ventilation is required for 

operating environment.

■ 

A few parts of the device shall be replaced regularly according

 to their average enduring time.

Quick

 

Start

 

Guide

Network

 

Camera

Camera

Quick

 

start

 

guide

CD

Water

-

proof

 

cap

Plastic

 

plug

 

×4

Drill

 

template

Sponge

Screwdriver

4 tapping screws PA 4×25 

enough to withstand 3 times the weight of the camera. Please install

and use the camera in the dry environment. You'd better install back 

the lower dome less than 4 hours after removing it. The mounting 

steps are as follows:

  Loosen the screws to open the lower dome and then loosen the

lock screw to remove the mounting base.

 

Before start, please make sure that the wall or ceiling is strong 

② 

Attach the drill template to the place where you want to fix the camera 

and then drill 4 screw holes and 1 cable hole (if you want to route the 

cables through the mounting base) according to the drill template. 

Lock

 

Screw

Lower

 

Dome

6

148

22

88 mm

89mm

CVBS&DC 
IN cables

N

et

w

or

k C

ab

le

8

9

10

RES

ET

TF

LINK

DC IN

CVBS

1

2

3

4

5

6

7

ALM-COM
ALM-NO
ALM-IN
ALM-GND


RS485T-

Microphone Cable

Headphone Cable

TF

 

Card

 

Slot

Reset

 

Hole

CVBS/DC IN port for testing

Alarm Input/Output

RS485 Cable

Video

 

Output

Network

 

Cable

Power

 

Cable

1

2

3

5

7

9

4

6

8

10

1 It

 

is

 

recommended

 

to

 

install

 

the

 

water

-

proof

 

cap

 

for

 

network

 

cable connection

.

2

 

If

 

the

 

switch

 

is

 

used

 

to

 

connect

 

the

 

camera

DC12V

 

power supply

 

is

 

not

 

required

.

PoE network 

① 

Loosen

 

the

 

nut

 

from

 

the

 

main

 

element.

② 

Run

 

the

 

network

 

cable (without

 

RJ 45

 

connector) through the

 both elements. Then

 

crimp

 

the

 

cable

 

with

 

RJ 45

 

connector

.

 

Connect

 

the

 

cable

 

to

 

the

 

hermetic

 

connector

Then

 

tighten

 

the

nut

 

and

 

the

 

main

 

cover

.

 

 

Alarm Input

: Join the grounding ends of the sensor and the camera 

and then connect the signal cable of the sensor to the alarm input 

port of the camera.

Alarm Output

: Loosen the screws in the alarm output port. Then

insert the signal wires of the alarm output devices into the port of 

NO and COM separately. Finally tighten the screws. Some of the 

external alarm output devices need the power supply. 

 

Connecting

 

Network

 

Cable

Alarm Connection

Reviews: