background image

SAFETY

 

WARNINGS

 

 

Always observe standard safety precautions during installation, operation and maintenance of this 
product.  To avoid the possibility of electrical shock, be sure to disconnect the power cord from the power 
source before you remove the IEC power fuses or perform any repairs. 

 

AVERTISSEMENTS

 

DE

 

SÉCURITÉ

 

 
Respectez toujours les précautions de sécurité standard lors de l'installation, du fonctionnement et de la 
maintenance de ce produit. Pour éviter tout risque de choc électrique, assurez-vous de débrancher le 
cordon d'alimentation de la source d'alimentation avant de retirer les fusibles d'alimentation CEI ou 
d'effectuer toute réparation. 

 

 

 
 

 

FCC

 

CLASS

 

A

 

INFORMATION

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation. 
 

Changes or modifications to this product not expressly approved by East Coast Datacom, Inc. 
could void the user's authority to operate the equipment.

 

PROPRIETARY

 

NOTICE

 

The information contained herein is proprietary to East Coast Datacom, Inc.  Any reproduction or 
redistribution of this publication, in whole or in part, is expressly prohibited unless written authorization 

is provided by East Coast Datacom, Inc. 
 

WARRANTY

 

NOTICE

 

WARRANTIES:  East Coast Datacom, Inc. (hereafter referred to as E.C.D.) warrants that its equipment is 
free from any defects in materials and workmanship.  The warranty period shall be three (3) years from 
the date of shipment.  E.C.D.'s sole obligation under its warranty is limited to the repair or replacement of 

defective equipment, provided it is returned to E.C.D., transportation prepaid, within a reasonable period.  
This warranty will not extend to equipment subjected to accident, misuse, alterations or repair not made 
by E.C.D. or authorized by E.C.D. in writing. 
 

 

 

 

CAUTION:

 FOR CONTINUED PROTECTION FROM RISK OF FIRE, 

REPLACE ONLY WITH SAME TYPE AND RATING FUSE. 

ATTENTION:

 POUR UNE PROTECTION CONTINUE CONTRE LES 

RISQUES D'INCENDIE, REMPLACEZ UNIQUEMENT AVEC UN 
MÊME TYPE ET UN FUSIBLE DE QUALITÉ. 

CAUTION:

 

RISK

 

OF

 

ELECTRIC

 

SHOCK:

 GROUNDED CONDUCTOR (NEUTRAL) PROVIDED 

WITH OVERCURRENT PROTECTION. TEST COMPONENTS BEFORE TOUCHING. 

ATTENTION:

 

RISQUE

 

DE

 

CHOC

 

ÉLECTRIQUE:

 CONDUCTEUR MIS À LA TERRE (NEUTRE) 

ÉQUIPÉ D'UNE PROTECTION CONTRE LES SURINTENSITÉS. TESTEZ LES COMPOSANTS 
AVANT DE TOUCHER. 

Summary of Contents for 101012














Reviews: