background image

3

The Easee Ready includes a backplate and a blind 

cover. By installing it you can extend your charging 

infrastructure at any time in the future. This is easily 

done with the Easee Plug & Play product by mounting 

the new Chargeberry in the empty Easee Ready 

backplate without the need of an electrician.

Intended use

This product is intended solely as a prepared charging 

point for an Easee Charging Robot.

The product must be firmly mounted on a wall or 

structure that covers the entire back side of the product 

and has a sufficient load-bearing capacity. It may only 

be operated with the approved operating parameters 

and under the specified environmental conditions (see 

page 4).

Uses other than those specified here are not permitted.

Conventions

This symbol indicates that the respective 

instructions must only be carried out by an 

authorised electrician.

This symbol indicates an immediate danger to 

life and health of individuals due to the effects 

of electrical energy. Non-observance of these 

instructions will result in serious damage to 

health – up to and including life-threatening 

injuries.

Introduction

Summary of Contents for Ready



















Reviews: