4
www.earthquakesound.com
Specifications are subject to change without notice
5
MiNi
FUNCTIONS AND FEATURES
D Stereo Amps
MiNi
FUNCTIONS AND FEATURES
D Stereo Amps
10
11
12
1
13
15
14
PWR
PROT
SPEAKER
FUSE
GND
REM
+12V
–
BRIDGE +
– L +
– R +
. . . . . .
. . . . . .
PWR
PROT
FUSE
. . . . . .
. . . . . .
GND
REM
+12V
+
BRIDGE
–
+
+
RL
RR
+
+
FR
FL
FUSE
+
+
+
+
GND
REM
+12V
BRIDGED
RR
RL
FL
FR
(4-Ohms)
10
11
12
13
14
MiNi D1000.4
BOOST
X-OVER
REAR
REAR
FRONT
FRONT
POWER
FREQ
GAIN
R
L
R
L
40Hz
400Hz MIN
0dB
12dB
X-OVER
BOOST
0dB
12dB
LPF
LPF
HPF
HPF
FLAT
FLAT
MAX
FREQ
40Hz
400Hz
GAIN
MIN
MAX
IN
IN
FLAT
MiNi D1500.2
INPUT
OUTPUT
LEVEL
SUBSONIC
10V
15Hz
AUTO ON
REMOTE ON
RESET
0.2V
30Hz
X-OVER
20Hz
LPF
HPF
FLAT
500Hz
R
R
L
L
9
7
8
6
5
2
3
3
3
4
4
1
1
5
2
6
4
9
3
POWER LED:
When lit up, the amplifier is functioning properly.
GAIN CONTROL:
Available only on the
D1000.4
, set based on the head unit’s
output voltage. Note, this is
not a volume control
. Always start at the MIN
and slowly increase the gain. Stop as soon as distortion is heard then lower
the gain until the distortion disappear and only clear sound is produced.
RCA INPUT:
Low level input of the
D1000.4
is
0.2V to 5V RMS
while the
D1500.2
&
D3000.4
is
0.2V to 10V RMS
. Be sure to use a HIGH LOW
LEVEL adaptor if the head unit has only speaker output.
XOVER SWITCH & FREQUENCY ADJUST:
Used to adjust the boosted center
frequency.
BASS BOOST:
Available only on the
D1000.4
, used to add 0 - 12dB to the
chosen center frequency.
LINE LEVEL CONTROL:
Available only on the
D1500.2
&
D3000.4
with a
range of
0.2V to 10V RMS
.
SUBSONIC FILTER:
Available only on the
D1500.2
&
D3000.4
, used to protect
the speakers from harmful low frequencies and DC Voltage. Note that the
subsonic filter only takes effect when the amplifier is in full range mode.
SIGNAL SENSING SWITCH:
Available only on the
D1500.2
&
D3000.4
.
Please refer to page 6-7 for the explanation of this feature.
RCA OUTPUT:
Available only on the
D1500.2
.
7
8
10
12
14
13
15
SPEAKER CONNECTION:
Each amplifier has bridgeable speaker outputs.
Note that the minimum impedance in bridged mode is
4-Ohm
.
GROUND TERMINAL:
Connect to vehicle’s chassis/ground using a short 4
gauge cable (2 feet maximum in length).
REMOTE TERMINAL:
Connect remote cable to the head unit’s remote
terminal. If multiple amplifiers are installed in the same system, additional
relays may be necessary.
+12V BATTERY TERMINAL:
Connect to battery positive (+) using a 4 gauge
cable.
FUSES:
Used as an added protection from damaging excessive current. Be
sure to use the proper fuse rating in your installation (see page 12).
PROTECTION LED:
Available only on the
D1500.2
&
D3000.4
. When lit up
upon powering on, the amplifier may be in self-test mode. If this LED stays
on, shut down the amplifier and locate what may have triggered the amplifier
to protection mode. If problem persists, call or e-mail our technical support
team for further assistance.
NOTE:
Be sure to follow the wiring preparations/guidelines as listed on the next
page to ensure proper installation.
11
