background image

2

 WARNING!

IMPORTANT: ‘WARNING !’ alerts user to a specific hazard

Other points are advisory which should be followed for safe use

ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS SUPPLIED WITH THIS PRODUCT 

AND THE MATERIAL BEING USED

Only use the unit as described in this manual. Additional product specific warnings may be found 

throughout the body of this manual where applicable.

FIRE AND EXPLOSION HAZARD
WARNING! 
The substances used with this Spray Gun (paints, coatings, solvents, etc.) may 

contain dangerous, harmful, explosive or corrosive materials.
WARNING! – Use extreme caution when spraying any materials with a flash point lower than 

100°F (38°C). Check the technical specifications on the paint or coating container before 

spraying.
• The Spray Gun must only be used with paints, coatings and solvents that have a flash point 

suitable for spraying. Consult the paint, coating or solvent manufacturer’s instructions and 

Safety Data Sheets.
• NEVER spray near an open flame including an appliance pilot flame.
• NEVER smoke while spraying.
• DO NOT operate light switches or run engines or similar spark producing products in the 

spray area if spraying solvents.
• DO NOT use any coatings or material containing any Halogenated Hydrocarbon constituent 

such as bleach and chlorine.
• Always disconnect unit from mains supply when filling the paint or coating container.
• Keep the turbine in a well - ventilated area.
• Keep the turbine as far removed from the spray area as the air hose will allow especially 

when using solvent based coatings.
EQUIPMENT MISUSE HAZARD
WARNING! 
The use of any accessory or attachment, other than those recommended in this 

instruction manual, may present a risk of personal injury.
WARNING! Use the Spray Gun only for the job it was designed for. Misuse of the Spray Gun 

will invalidate the guarantee.
WARNING! If the cordset is damaged, it must be replaced with the correct Earlex part to avoid 

a hazard.
WARNING! To reduce the risk of electric shock do not expose to water. Store indoors.
• NEVER under any circumstances aim the Spray Gun at another person or animal. In the 

event of an injury seek expert medical advice immediately.
• NEVER carry the turbine while spraying.
• Always ensure there is adequate ventilation when spraying.
• After each use, thoroughly clean the Spray Gun and grease the Fluid Needle.
• This appliance can be used by persons aged from 14 years and above and persons with 

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they 

have been given supervision or instruction concerning use of the appliance in a safe way and 

understand the hazards involved.
• Use only genuine manufacturer replacement parts.
• Always disconnect the unit from the power supply before cleaning.
• If using with 3rd party turbine - refer to manufacturers instructions.
PERSONAL PROTECTIVE EQUIPMENT
WARNING! 
Noise levels exceed 85dB. Therefore suitable ear protection must be worn.
• Always wear a suitable protective mask when spraying. The use of gloves, goggles and 

overalls is also recommended.
HOT SURFACE
• CAUTION: Outlet of turbine and air hose may become hot during use. Please allow to cool 

before removing air hose.

Summary of Contents for Pro-8













Reviews: