Eanmay ST-VGT Instruction Manual Download Page 22

Page: 22 / 74

4.4 GSM Alarm Receiving (on-site intercom added)

When alarm occurs, it will send SMS first, then call the preset voice number, when

pick up the call, it will play the recorded voice message first, then voice prompt:

Press 1 to cancel alarm,

Press 2 to check alarm event,

Press 3 to arm system,

Press 4 to disarm system,

Press 5 to Stay arm,

Press 6 to enable siren,

Press 7 to listen-in,

Press 8 to control programmable output port,

Press 9 to talk-back,

Press 0 to Disconnect.

4.5 GSM control via SMS

Arm Command

#PWD1234#arm

Disarm Command

#PWD1234#disarm

Home Arm Command

#PWD1234#home

Status Checking command

#PWD1234#check

Enable programmable output port

#PWD1234#PGM open

Disable programmable output port

#PWD1234#PGM close

Enable appliance switch command

#PWD1234#switch open 01

Disable appliance switch command

#PWD1234#switch off 01

Note: the factory default user code is 1234, when arm successfully, SMS auto reply”

arm successfully”, if the password is correct, the command is not correct, SMS will

reply” operation failure”, if the password is not correct, no SMS reply.

Summary of Contents for ST-VGT











































































Search results

Summary of Contents for ST-VGT

Reviews:

Related manuals for ST-VGT

Brands by name

Popular brands

Eanmay ST-VGT, Instruction Manual

Search results

Summary of Contents for ST-VGT

Reviews:

Related manuals for ST-VGT

Brands by name

Popular brands