Charging
For rechargeable models, use EAGTAC
DC power adapter (see below), or
EAGTAC 12V car charger to charge.
Remove the water-proof cap and insert
the charging plug to charge (store the
cap next to the charging socket).
Replace the water-seal cap after charg-
ing is complete.
* If the battery is nearly drained, it may only reach to
90%+ capacity with the three hours timer. To reset the
timer, simply remove and re-insert the charging plug
anytime during charge.
** Since the charging circuit and LED driver share the
common output. The secondary LED may flash or light
up in very dim output when user starts up or operates
the flashlight. This is normal.
*This may or may not show in your flashlight, because
the protection board on the li-ion battery may shut off
the battery before the LED circuit picks up the battery
critical signal.
How to prolong battery life
1) Recharge often. Do not continuously
discharge the battery completely. Li-ion
batteries has no memory effect.
2) When the flashlight is going to be put
in storage for a long time, drain the
battery to under 50% capacity for best
battery life.
Our advice that you turn off the flash-
light during charging for fast and full
charge. The charging circuit uses
constant current and constant voltage
method to charge the li-ion batteries
quickly and safely. The secondary LED
turns on in solid blue color during fast
charge state. When the battery is full,
the indicator turns dim. A built-in
countdown timer* is implemented to
shut off the charging circuit within 3
hours (or 7 hours for special models).
User may remove the charger plug
shortly after the charging indicator
turns dim for immediate usage.
Battery level indicator
Reports approximate battery life for ten
seconds after changing output level or
clicking the button switch. When
battery level is very low, main LED will
flash once every 30 seconds*. Reduce
the output to extend battery runtime.
Blue
Red
Red (flash)
60%-100%
25%-60%
0%-25%
20%-100%
5%-20%
0%-5%
LED
Center
Disk
LED
Turbo output Lower output
Secondary LED
Secondary LED**
Charge status
Blue
Blue (dim)
LED off
Fast charge
Charge complete
Charging timer expire
Models
GX
SX/MX
Model specific Charger
10V 1.2A or 12V 1A
10V 1.8A or 12V 1.5A
Watt
12W
18W
Maintenance
Periodically clean the thread and o-rings
with a lint free cloth and apply a thin coat-
ing of EagleTac silicon-based lubricant to
the o-rings (not the machined thread).
Clean the battery contact, signal contact
(the silver node at the back of the head
and the plate on the body tube), thread,
and body contact (conductive aluminum
area and) with a lint free cloth and use a
small drop of Deoxit red cleaner solution
(D series) to slightly lube them for better
conductivity and smoother mode switch-
ing experience.
Color and diffuser filter
For models that comes with filter
upgrade. Unscrew the stainless steel
bezel and replace it with the threaded
filter.
1) Charge your flashlight or battery
2) Ensure tailcap is tight
3) Clean all conductive contacts
(see maintenance section)
4) Check battery polarity
Troubleshooting - Flashlight does not
turn on or fails to switch between
outputs normally:
“No Hassle” EAGTAC Warranty
For repair, replacement, or other inquiries
contact your EAGTAC dealer. You can also
reach our customer support via email at
[email protected].
We warrant our flashlights to be free from
defects in workmanship and materials. We will
repair, replace at our option, without charging
any product or part which is found to be
defective under normal use within 120
months from the date of purchase with the
proof of purchase.
Electronics, chargers and rechargeable batter-
ies are covered for a period of 12 months with
purchase receipt. Such repair or replacement
shall be the purchaser’s sole and exclusive
remedy under this warranty. Normal wear and
tear including batteries draining is not
covered, nor is damage resulting from modifi-
cation, misuse, abuse, neglect, faulty battery,
battery leakage, improper maintenance or
repaired by anyone other than EAGTAC or
authorized dealer.
Do not touch or attempt to clean the
reflector, as it will damage the reflective
coating permanently.
*GX model shown using filter housing w/ flip-over feature.
SX and MX model uses standard individual filter add-on.
Instant Turbo output
At any output level,
press and hold
the
flashlight for 100% output.
Release
the
button to return to previous level.
Instant Strobe output
At any output level (even off),
double
press and hold
the on/off button switch
for strobe output.
Release
the button to
return to previous level.
Energy saving feature
This feature reduce output by 20%
after 200 seconds at turbo mode.
Turbo head upgrade
We offer a turbo head upgrade head
for tighter beam and brighter hot spot.
To exchange the head, un-twist the
head and replace it with the turbo
head. (Important) Ensure the LED and
LED center disc is centered inside the
reflector before tightening the head,
or it may damage the LED.
“Deoxit” is a trademark of Caig Laboratories, Inc.
Periodically apply
Deoxit red here
and here
to ensure
mode switching
and output
stability in long term.
