2
eagletone.com
eagletone.com
3
User’s manual
EAGLETONE LED PAR 4 LIVE
EAGLETONE LED PAR 4 LIVE
User’s manual
UNPACKING
Thank you for purchasing our PARLED9W. Every PARLED9W has been carefully tested and
shipped in perfect operating condition. When receiving our products, carefully check the
shipping carton for damage that might have happened during transport. In case of damage,
inspect the fixture for any damage or missing accessories necessary to operate it. Please do
not take any action without first contacting us.
SAFETY INSTRUCTIONS
• Please keep this User’s Manual for future reference. If you sell the unit to another user, be
sure that he also receives this instruction booklet.
• Unpack and check the unit carefully that it has not been damaged during transport before
using the unit.
• Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
• The unit is for indoor use only in a dry location.
• The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
• Disconnect mains power before fuse replacement or servicing.
• Replace fuse only with the same type.
• Make sure there are no inflammable materials close to the unit during operation.
• Use safety cable when fixing this unit.
• In the event of serious operating problem, stop using the unit immediately.
• Never try to repair the unit by yourself. Repair carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance center
and always use the same type of spare parts.
• Do not touch any wires during operation as high voltage might be causing electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or any
moisture.
• If this unit will not be used for a long period of time, disconnect if from power supply.
GENERAL INSTRUCTIONS
First familiarize yourself with the basic operation principles of this unit by reading the attached
user manual carefully. These instructions contain important safety information regarding the
use and maintenance of this unit.
SYSTEM MENU
DMX ADDRESS SETTING
1. Tap either the MENU, UP or DOWN buttons until “ADDR” is displayed, then press ENTER.
2. Press the UP or DOWN buttons to indicate your desired address (A001 to A512).
Leave the display on this address and after a few seconds the address will be saved
into memory.
CHANNEL DMX MODE
This will let you switch between 6 Channel DMX mode and 2Ch/3Ch/4Ch/6Ch/7Ch/14Ch
Channel DMX mode.
1. Tap either the MENU, UP or DOWN buttons until “CHMD” is displayed, then press ENTER.
2. Tap the UP or DOWN buttons to choose your desired DMX mode (2Ch to 14Ch) and press
ENTER to confirm and exit.
MASTER/SLAVE CONFIGURATION
This will let you set the unit as a master or slave in a master/slave configuration.
1. Tap either the MENU, UP or DOWN buttons until “SLMD” is displayed, then press ENTER.
2. Tap the UP or DOWN buttons to choose your desired setting (SL01 to SL04) and press
ENTER to confirm and exit.
SOUND ACTIVE SHOW SETTING
In this mode, you can choose your desired sound activated show.
1. Tap either the MENU, UP or DOWN buttons until “SOUM” is displayed, then press ENTER.
2. Tap the UP or DOWN buttons to choose your desired setting (S-01 to S-12) and press ENTER
to confirm and exit.
PRESET SHOWS
In this mode, you can choose your desired stand-alone shows. You have a total of 25 preset
shows to choose from.
1. Tap either the MENU, UP or DOWN buttons until “AUTO” is displayed, then press ENTER.
2. Tap the UP or DOWN buttons to choose your desired show (Pr01 to Pr25) and press ENTER
to confirm and exit.
SHOWS SPEED
In this mode you can adjust stand-alone shows speed and sound activated sensitivity.
1. Tap either the MENU, UP or DOWN buttons until “SPEE” is displayed, then press ENTER.
2. Tap the UP or DOWN buttons to choose your desired setting (S001 to S255) and press ENTER
to confirm and exit.
BLACKOUT OR STAND BY MODE
1. Tap either the MENU, UP or DOWN buttons until “blMd” is displayed, then press ENTER.
2. To activate Blackout mode, tap the UP or DOWN buttons until “YES” is displayed, press
ENTER to confirm and exit. To deactivate Blackout mode, select “NO” and press ENTER.
DISPLAY
This function will reverse the display 180°.
1. Tap either the MENU, UP, or DOWN buttons until “dISP” is displayed, then press ENTER.
2. To activate this function, tap the UP or DOWN buttons until “YES” is displayed, press ENTER
to confirm and exit. To deactivate, select “NO” and press ENTER.
