manualshive.com logo in svg

Eagle AVI, Installation & Owner'S Manual

Share
Download
Eagle AVI Installation & Owner'S Manual Download Page 6

4

AVI Slide Rev - C

Gener

al Safety

Important Safety Information

General Safety Information

Install Warning Signs

Installing Opening Devices

1.  Never let children operate or play with gate controls. Keep the remote control away from children.

2.  Always keep people and objects away from gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.

3.  Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object activates the non-contact 
sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly can 
increase the risk of injury or death.

4.  Use the emergency release ONLY when the gate is not moving and verify that operator power has been turned OFF.

5.  KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate hardware.

6.  The entrance is for vehicles only. Pedestrians must use separate entrance.

7.  BE SURE TO CONTINUE TO KNOW AND PRACTICE THESE INSTRUCTIONS. SAVE THESE INSTRUCTIONS

To reduce the risk of injury or death read and follow the instructions

WARNING

Be sure to read and follow all the Eagle Access Control Systems, Inc. before installing and operating any Eagle 
Access Control System, Inc. products. Eagle Access Control Systems, Inc. is not responsible for any improper 
installation procedures caused by failure to comply with local building codes.

Install warning signs on 

BOTH

 sides of the gate.

Be sure to mount gate operating 
devices at least six feet (6’) away from 
any moving part of the gate. They 
must 

NOT

 be able to be operated 

reaching through the closed gate.

CAUTION

Moving Gate Can Cause
Serious Injury or Death

KEEP CLEAR!  Gate may move at any time
without prior warning.

Do not let children operate the gate or play
in the gate area.

This entrance is for vehicles only.
Pedestrians must use separate entrance.

Moving Gate Can Cause
Serious Injury or Death

KEEP CLEAR!  Gate may move at any time
without prior warning.

Do not let children operate the gate or play
in the gate area.

This entrance is for vehicles only.
Pedestrians must use separate entrance.

Moving Gate Can Cause
Serious Injury or Death

KEEP CLEAR!  Gate may move at any time
without prior warning.

Do not let children operate the gate or play
in the gate area.

This entrance is for vehicles only.
Pedestrians must use separate entrance.

Closing Gate

Summary of Contents for AVI

























Reviews:

No comments

Brands by name

Popular brands

Load more brands