TKS510ET SILVER SERIES
OPERATION AND MAINTENANCE
Page 7
5.1 - ROUTINE MAINTENANCE
ALL ROUTINE MAINTENANCE AND SPECIAL MAINTE-
NANCE MUST BE CARRIED OUT BY COMPETENT
PERSONNEL OR BY ANAUTHORISED SERVICE CENTRE.
ALWAYS USE ORIGINAL SPARE PARTS. ATTENTION ALL
MAINTENANCE OPERATIONS MUST BE CARRIED OUT
WITH THE MACHINE OFF.
5.2 - BATTERY MAINTENANCE
The battery must be kept clean and dry. Keep the terminals and poles
clean. Every 10 hours,remove the caps and check the electrolyte level.
If necessary top up with distilled water.
The battery should be serviced in a properly ventilated area. During
this operation, do not expose the battery to naked flames and do not
smoke. The battery has a 3 hours working life; if you notice that it is
much shorter, check that:
* the brushes are not obstructed;
* the battery is completely charged.
5.2.1 - BATTERY RECHARGE
When the machine is off:
- remove the caps from ther battery cells.
- Top up with distilled water.
- Plug in a battery charger
pos. 3 Fig 3
bearing up to
12V
10A
.
The life of the battery will depend on its routine maintenanceand on
ists discharge level. Do not allow the battery charge to drop below the
limit signalled by indicator lights
pos. 4 Fig. 3.
Got to the max.
discharge level, the machine stops and neet to be re-charge in order
to restart working.
Charge indicator lights
Green light:
The battery is charged.
Yellow light:
The battery is running out; recharge as soon as
possible.
Red light:
The battery has run out.
DO NOT
operate the
machine.
Every
200
hours of work,check the state of the motor carbon brushes
and replacethem if they are worn.
Always try to replace them before they reach
1000
hours of work.
X
X
X
X
X
X
X
X
CHECK
On delivery
Every 10 hours
Every 50 hours
Every 100 hours
Check the battery liquid
The belts for slackening
The tightness of nuts and screws
The brushes for wear
The gaskets for wear and leakages
If all the functions are in working
order
5.3 - FILTER MAITENANCE
Cleaning the filter
The filter is one of the machine main components. It is essential for
the best results from your machine. If you notice that dust forms when
the machine is at work, check the filter.
The filter is cleaned as follows:
A)
Press and release the lever of the appropriate filter shaker
pos. 7
Fig. 3
. The lever operates a rod that will unclog the filter. Repeat
this operation 5 or 6 times.
Eletric filtershaker version (optional)
A)
By means of the button
pos. 10 Fig. 3
the electric filtershaker is
activated. For the filter cleaning keep the button pressed for 5
seconds roughly. Repeat the operation 3 o 4 times.
B)
Apart from the filter shaker,it is advisable every now and again to
remove the machine’s filterand clean it out with a blast of air or
a vacuum cleaner. For this purpose,the filter is removed as
follows:
- remove the rear bin.
- Remove the filter stopping device
pos. 1 Fig. 6.
- Remove the filter
pos. 3 Fig. 6
while holding up thefilter shaker
rod.
- To remount the filter
pos. 3 Fig. 6,
carry out the operation in
reverse order.
ATTENTION:
the filter features an arrow that shows you the
direction in wich it should be fitted.
Dusty environments
If you are using the machine in a particularly dusty environment
(cement factories, sawmills, marble processing factories), it is wise to
use the filter shaker more frequently.
Replacing the filter
Every 200 hours of work, the filter must be replaced. Follow the
operations listed in point B).
After the filter has been remounted,make sure the gasket and filter are
dust tight.
WASTES MUST BE DISPOSED OF IN ACCORDANCE TO
THE LAW.
Fig. 6