background image

4

OPERATING MANUAL AND INSTRUCTIONS

CHAIN-MOUNTED UNITS

Chain supplied by Eagle Group is constructed of sufficient strength to securely hold the weight of the RedHots

®

Heat Lamp when properly

mounted. (Ordered separately by the foot under Eagle Group, part # 358372.) 

Securely fasten the chain to surface above the area that the heat lamp will be located over. Please be sure that the chain is located so that

the heat lamp will be suspended at a safe and proper distance from any side, rear walls and working surface. (Distances provided in

“Mounting Location” section of this manual—page 3.)

Loosen the screws that hold that mounting tabs on either side of the heat lamp. Extend the tabs upward and then tighten the screws. 

Use a short piece of chain between the two tabs. Attach the overhead chain to the connecting chain to form a “Y” shape (see illustration

below) and repeat for the opposite end. 

Note: Additional chain is required to mount from overhead to each tab. 

WARNING

Chain must be #8 trade size and securely fastened, 

or unit could come loose and possibly cause personal injury or damage to the unit. 

“Y” shape chain connection

(part #358372—ordered per foot)

chain-mounted

heat lamp

(end view)

shelf

bracket 

(part #355148)

#8-32

screws

#1/4-20 screws

(not included)

heat lamp 

UNDER SHELF MOUNT

When mounting the heat lamp under a shelf, maintain a 1˝ offset from the bottom of the shelf. The heat lamp is not to be mounted

under a shelf that is considered combustible. The shelf must be made of a non-combustible material.

If the shelf has a rolled edge or downturn, the heat lamp must be below the lowest part of the roll or flanged edge, using the adjustable

bracket (supplied by Eagle Group, part #355148). The lower set of holes accommodates a 1-1/2˝ deep shelf. 

Remove the two #8-32 screws per bracket, towards the rear of the heat lamp (shown in the illustration below), and remove any

hanging clips. Align the holes in the bracket to the holes in the heat lamp, as shown below, and securely mount the screws. 

Secure the heat lamp brackets using #1/4-20 bolts/screws (hardware not provided by Eagle Group) to ensure a secure installation. 

Summary of Contents for RedHots RHHL Series









Reviews: