Notes for assembly:
• When assembling plastic split sleeves onto posts, be sure the thicker part of the taper goes toward the bottom. Make
sure the rib inside split sleeve is seated into groove on the post.
• When installing 3-sided frame, shelves, and mouse shelf (sold separately), be sure the thicker part of the collars goes
toward the bottom.
48˝ posts
33˝
posts
Figure 1b
3-sided
frame
Install 3-sided frame
1
a) Assemble plastic split
sleeves onto 2˝ mark on all
posts (see
Figure 1a
).
b) Insert posts through collars
of 3-sided frame as shown
in
Figure 1b.
Slide 3-sided
frame down onto split
sleeves. 33˝ posts should
indicate front of unit.
Note: Bottom of
each post is
the end with
groove 1
7
/
16
˝
from the end.
split
sleeves
2˝ mark
Figure 1a
Assembly is complete.
48˝
posts
Figure 5
cantilever shelf
Install 12˝ x 24˝ cantilever shelf
5
a) Assemble split sleeves onto
48˝ mark on 48˝ posts.
b) Insert 48˝ posts through
cantilever shelf collars and
slide shelf down onto split
sleeves (see
Figure 5
).
Install 14˝ x 24˝
wire undershelf
a) Assemble plastic split
sleeves onto topmost mark
on both 7˝ posts.
b) Assemble wire shelf to
7˝ posts (see
Figure 2a
).
c) Assemble plastic split
sleeves onto 9˝ mark
on 48˝ posts.
d) Insert the 48˝ posts
through remaining
undershelf collars and
slide assembly down
onto split sleeves.
7˝ posts should rest
on 3-sided frame
(see
Figure 2b
).
2
Figure 2a
wire undershelf
7˝ posts
48˝
posts
under-
shelf
3-sided
frame
Figure 2b
Install 24˝ x 24˝ wire shelf tabletop
a) Assemble split sleeves onto 32˝ mark on all posts.
b) Position shelf over 4
vertical posts and
slide down until shelf
collars seat on plastic
split sleeves.
Note: Shelf trusses
should run left-to-right
as shown.
4
Figure 4
48˝
posts
24˝ x 24˝
shelf
Figure 3
mouse pad
Install mouse shelf (sold separately)
3
a) Assemble split sleeve onto 29˝ mark on
either left or right 33˝ post (see
Figure 3
),
depending on preference.
b) Slide the mouse shelf collar down the post
and onto split sleeve. Mouse shelf should
be able to swivel on split sleeve and post.
33˝ post
split sleeve
Note: Install casters with brakes onto
the 33˝ posts.
a) Gently lay unit on its side or back,
giving access to bottom of posts.
b) Install donut bumper onto bottom
of each post.
c) Insert caster stem into bottom of
each post. Drive caster in, using a
hammer or mallet. Several solid
hits are usually required.
post
donut
bumper
caster
stem
Figure 7
7
Assemble casters to posts
Figure 6
Install keyboard drawer
6
a) Position
keyboard drawer
under tabletop.
b) Hook drawer
slides over
outermost front-
to-back trusses
of tabletop on
each side.
keyboard
drawer
tabletop
shelf
truss
eagle Foodservice equipment, eagle Mhc, and specFAB
®
are divisions of eagle Group. ©2021 by the eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: 302/653-3000 • 800/441-8440
• Fax: 302/653-2065 • www.eaglegrp.com
(End)
