background image

 

Never let children operate or play with gate controls. Keep the remote control away from 

 children.

 

Always keep people and objects away from gate while the gate is in operation. NO ONE

 

SHOULD CROSS THE PATH OF A MOVING GATE.

 

Test the gate operator monthly. The gate must reverse on contact with a rigid object or stop

 

when an object activates the non-contact sensors.  After adjusting the force or the limit of 

 

travel, retest the gate operator. Failure to adjust and retest the gate operator properly can

 

increase the risk of injury or death.

 

Use the emergency release only when the gate is not moving. Make sure the power for the 

 

gate operator is off.

 

KEEP GATES PROPERLY MAINTAINED. Read and follow the manual. Have a qualified

 

service person make repairs to the gate or gate hardware.

 

The entrance is for vehicles only. Pedestrians must use separate entrance. 

UL Listings

Essential Safety Procedures

WARNING - TO REDUCE THE RISK OF INJURY OR DEATH - READ AND FOLLOW ALL INSTRUCTIONS:  

BE SURE TO CONTINUE TO KNOW AND PRACTICE THESE INSTRUCTIONS

(4)

         Distributed by AFW Access Systems • www.AnchorMiami.com/afwas

Vehicular horizontal slide-gate operator (or
system)

 - A vehicular gate operator (or system)

that controls a gate which slides in a horizontal 
direction that is intended for use for vehicular 
entrance or exit to a drive, parking lot, or the like.

UL Listings

__________________________________________

Gate

 - A moving barrier such as a swinging,

sliding, raising, lowering, rolling, or like barrier
that is a stand-alone passage barrier or is that
portion of a wall or fence system that controls 
entrance and/or egress by persons or vehicles
and completes the perimeter of a defined area.

__________________________________________

Residential vehicular gate operator - Class I

 - 

A vehicular gate operator (or system) intended 
for use in a home of one to four single family
dwellings, or a garage or parking area associated 
therewith.

Commercial / General access vehicular gate 
operator - Class II

 - A vehicular gate operator

(or system) intended for use in a commercial
location or building such as a multi-family
housing unit (five or more single family units),
hotel, garages, retail store, or other buildings 
servicing the general public.

Commercial / General access vehicular gate
operator - Class III

 - A vehicular gate operator

(or system) intended for use in an industrial 
location, loading dock area, or other location 
not intended to service the general public.

Commercial / General access vehicular gate
operator - Class IV

 - A vehicular gate operator

(or system) intended for use in a guarded
industrial location or buildings such as airport
security area or other restricted access 
locations not servicing the general public, in 
which unauthorized access is prevented via 
supervision by security personnel.

Summary of Contents for Eagle-2000 series


























Reviews: