E2S Warning Signals
Impress House, Mansell Road, Acton, London W3 7QH
[email protected] e2s.com
Page 1 of 2
D242
-
00
-
601
-
IS_Issue_2
-
03/06/2021
INSTRUCTION & SERVICE MANUAL
SONFL1H Range
-
Alarm Horn & L.E.D Beacon
Model No.
Nominal Voltage
Voltage Range
Horn Nom.
Current
Beacon Nom.
Current
Sound Pressure Level dB(A)
Max
Nominal
100.0 @ 1m
91.0 @ 3m
99.0 @ 1m
90.0 @ 3m
SONFL1HDC012
…[
X]/[Y]
12V dc
10
-
14V dc
25mA*
79.5mA
SONFL1HDC024
…[
X]/[Y]
24V dc
20
-
28V dc
25mA*
87mA
SONFL1HAC115
…[
X]/[Y]
115V ac 50/60Hz
+/
-
10%
27mA
34mA
SONFL1HAC230
…[
X]/[Y]
230V ac 50/60Hz
+/
-
10%
39mA
19mA
*Current at nominal voltage on Tone 2
[X] Denotes Housing Colour: R = Red; G = Grey; W = White
[Y] Denotes Lens Colour: A = Amber; B = Blue; C = Clear; G = Green; M = Magenta; R = Red; Y = Yellow
SONFL1H Combined Sounder & L.E.D Beacon
10 Selectable Tones & 2 Stages
High Output L.E.D Array
8 Flash Modes:
Steady On
Flashing
-
1Hz, 1.5Hz, 2Hz
Double Strike, Triple Strike, Temporal, Blinking
CE, EAC Approved
UL / cULus Approved
IP Rating: Type 3R / 13, IP66
Beacon is General Signalling Approved for US & Canada
UL1638A & CSA22.2
-
205
-
17
Clear Lens Beacon is Private Mode Fire Approved
for US & Canada UL1638, CAN/ULC
-
S526
Use suitable conduit or cable glands with
suitable IP or type rating
0.4Nm
5
0.5 1.5mm
Terminal Connections
SONFL1H
Dimensions: 172 x 86 x 83mm
Cable Entry: 2
-
off M20 x 1.5mm
Temp:
-
40°C to +55°C
Unit weight: 0.46Kg
Attention: Installation must be carried out by an electrician in compliance with the latest codes and regulations.
Attention: L'installation doit être effectuée par un électricien conformément aux derniers codes et réglementations.
Achtung: Die Installation muss von einem Elektriker gemäß den neuesten Vorschriften und Bestimmungen durchgeführt wer
den.
Attenzione: L'installazione deve essere eseguita da un elettricista in conformità con i codici e le normative più recenti.
Atención: La instalación debe ser realizada por un electricista de acuerdo con los últimos códigos y regulaciones.
Atenção: A instalação deve ser realizada por um eletricista de acordo com os códigos e regulamentos mais recentes.
Внимание
:
установка должна выполняться электриком в соответствии с последними нормами и правилами
.
Attention: Disconnect from power source before installation or service to prevent electric shock
Attention: Débranchez
-
le de la source d'alimentation avant l'installation ou l'entretien pour éviter tout choc électrique.
Achtung: Vor Installation oder Wartung von der Stromquelle trennen, um einen Stromschlag zu vermeiden.
Attenzione: scollegare dall'alimentazione prima dell'installazione o dell'assistenza per evitare scosse elettriche.
Atención: desconéctelo de la fuente de alimentación antes de la instalación o el servicio para evitar descargas eléctricas.
Atenção: Desconecte da fonte de alimentação antes da instalação ou serviço para evitar choque elétrico
No liability is accepted for any consequences of the use of this document. The technical specification of this unit is subject to change without notice due to our policy of continual
product development. All dimensions/weights are approximate. This unit is sold subject to our standard conditions of sale, a copy of which is available on request.
AC Circuit
DC Circuit
See D242
-
06
-
601
-
Schematic Wiring
DC
AC
