background image

 

European Safety Systems Ltd.

   Impress House, Mansell Road, Acton, London W3 7QH

 

www.e2s.com

 

Tel: +44 (0)208 743 8880

 

Document No. D156-00-621-IS

 

Issue 1

 

27-10-22

 

 

Sheet 2 of 15

 

 

3.1. ATEX / IECEx / UKEX Ratings 

 

Standards 

EN IEC 60079-0:2018 / IEC60079-0:2017 (Ed 7): 

Explosive Atmospheres - Equipment. General Requirements 

EN60079-1:2014 / IEC60079-1:2014 (Ed 7): 

Explosive Atmospheres - Equipment Protection by Flameproof 
Enclosures "d" 

BS EN 60079-31:2014 / IEC 60079-31:2013 (Ed 2): 

Explosive Atmospheres - Equipment Dust Ignition Protection by 
Enclosure "t" 

Ratings 

GNExB2X05 
DC024-S 

Ex db IIC T5 Gb Ta -50°C to +70°C 
Ex db IIC T6 Gb Ta -50°C to +60°C 
Ex tb IIIC T89°C Db Ta -50°C to +70°C 

GNExB2X10 
DC024-S 

Ex db IIC T4 Gb Ta -50°C to +70°C 
Ex db IIC T5 Gb Ta -50°C to +45°C 
Ex tb IIIC T117°C Db Ta -50°C to +70°C 

GNExB2X15 
DC024-S 

Ex db IIC T4 Gb Ta -50°C to +70°C 
Ex tb IIIC T125°C Db Ta -55°C to +70°C 

 

Certificate No. 

DEMKO 15ATEX1448X 
IECEx UL15.0003X 
UL21UKEX2136X 

ATEX Mark, Equipment 
Group and Category: 

 

II 2G 
II 2D

 

CE Marking and 
Notified Body No. 

 

2813 

UKCA Marking and 
Notified Body No. 

 

0518 

 

3.2. NEC / CEC Ratings 

 

 

 
All  models  are  approved  for  use  as  Visual  Signal  Device  for 
use as General Signalling: 
 

UL1638A & CSA C22.2 No 205-17 

 

NEC Class / Zone Ratings US Codes 

 

Standards 

UL 60079-0 (Ed. 7) 04/15/2020 

Explosive Atmospheres - part 0: Equipment - General 
Requirements  

UL 60079-1 (Ed. 7) 2015 

Explosive Atmospheres - Part 1: Equipment Protection by 
Flameproof Enclosures 'd' 

Ratings 

GNExB2X05 
DC024-S 

Class I Zone 1 AEx db IIC T5 Gb Ta -50°C to +70°C 
Class I Zone 1 AEx db IIC T6 Gb Ta -50°C to +60°C 

GNExB2X10 
DC024-S 

Class I Zone 1 AEx db IIC T4 Gb Ta -50°C to +70°C 
Class I Zone 1 AEx db IIC T5 Gb Ta -50°C to +45°C 

 
Installation  must  be  carried  out  in  compliance  with  the 
National Electric Code. 
 

CEC Class / Zone Ratings Canada 

 

Standards 

CAN/CSA C22.2 No. 60079-0 (Ed. 4) 02/2019 

Explosive Atmospheres - Part 0: Equipment - General 
Requirements  

CAN/CSA C22.2 No. 60079-1 (Ed. 3) 2016 

Electrical Apparatus for Explosive Gas Atmospheres - Part 1: 
Flameproof Enclosures 'd' 

Rating 

GNExB2X05 
DC024-S

 

Ex db IIC T5 Gb Ta -50°C to +70°C 
Ex db IIC T6 Gb Ta -50°C to +60°C 

GNExB2X10 
DC024-S

 

Ex db IIC T4 Gb Ta -50°C to +70°C 
Ex db IIC T5 Gb Ta -50°C to +45°C 

 
Installation  must  be  carried  out  in  compliance  with  the 
Canadian Electric Code. 
 

NEC & CEC Class / Division Ratings for US / Canada, 
USL CNL 
 

Standards 

GNExB2X 
Xenon 
beacons 

UL1638A (Ed. 1) 2016 

Standard for Visual Signal Appliances for General 
Signalling Use  

CSA C22.2 No. 205-17 (Ed. 3) 2017 

Signal Equipment 

Ratings 

GNExB2X05 
DC024-S 

Class I Div 2 Group ABCD T5 Ta -50°C to +70°C 
Class I Div 2 Group ABCD T6 Ta -50°C to +60°C 

GNExB2X10 
DC024-S 

Class I Div 2 Group ABCD T4 Ta -50°C to +70°C 
Class I Div 2 Group ABCD T5 Ta -50°C to +45°C 
 

 
The certification approval has validated continuous use up to 
38°C ambient and are for transient use up to 70°C ambient. 
 
Installation  must  be  carried  out  in  compliance  with  the 
National Electric Code / Canadian Electric Code. 
 

4)  Zones, Gas Group, Category and 

Temperature Classification 

 
The  units  can  be  installed  in  locations  with  the  following 
conditions: 
 

Area Classification 

Zone 1 

Explosive gas air mixture likely to occur in normal 
operation. 

Zone 2 

Explosive gas air mixture not likely to occur in 
normal operation, and if it does, it will only exist 
for a short time. 

Zone 21 

(ATEX / IECEx / 
UKEX only)

 

Explosive dust air mixture likely to occur in 
normal operation. 

Zone 22 

(ATEX / IECEx / 
UKEX only)

 

Explosive dust air mixture not likely to occur in 
normal operation, and if it does, it will only exist 
for a short time. 

Gas Groupings 

Group IIA 

Propane 

Group IIB 

Ethylene 

Group IIC 

Hydrogen and Acetylene 

Summary of Contents for GNExB2X05 Series





















Reviews: