E2S BExCBL2-L2D-P Instruction Manual Download Page 5

Page: 5 / 12

European Safety Systems Ltd.

Impress House, Mansell Road, Acton, London W3 7QH

www.e2s.com

Tel: +44 (0)208 743 8880

Document No. D210-00-721-IS

Issue 5

12-09-2022

Sheet 5 of 6

11. AC Wiring

A 4-way terminal block is provided on the AC chamber beacon
for power. There are 2-off Live and 2-off Neutral terminals in
total. A 4-way terminal block is provided on the AC cover
beacon for power. There are 2-off Live and 2-off Neutral
terminals in total.

Fig. 5 AC Terminals

12. DC Wiring

A 4-way terminal block is provided on the DC chamber beacon
for power. There are 2-off +ve and 2-off -ve terminals in total.
A 4-way terminal block is provided on the AC cover beacon for
power. There are 2-off +ve and 2-off -ve terminals in total.

Fig. 6 DC Terminals

12.1

Line Monitoring

On BExCBGL2-L2D DC units, dc reverse line monitoring can
be used if required. All DC sounders have a blocking diode
fitted in their supply input lines. An end of line monitoring diode
or an end of line monitoring resistor can be connected across
the +ve and –ve terminals. If an end of line resistor is used it
must have a minimum resistance value of 3k3Ω and a
minimum power rating of 0.5 watts or a minimum resistance
value of 500Ω and a minimum power rating of 2 watts.

The resistor must be connected directly across the +ve and -
ve terminals as shown in the following drawing. The resistor
leads should be kept as short as possible.

Fig. 7 End of Line Resistor Placement

13. Flash Rate Settings

The BExB2L2D beacons can produce different flash patterns
as shown in Table 1. The flash patterns are selected by
operation of the flash setting DIP switch on the PCB, Fig 9.

Fig. 8: DIP Switch Location

Table 1: Switch Positions for Flash Patterns

Switch

Setting

S1 Mode

S2 Mode

S3 Mode

(123456)

(DC & AC)

(DC Only)

000000

Steady High

Power

Flashing 1Hz

Flashing Triple

Strike

000001

Steady Low

Power

Flashing 1Hz

Flashing Triple

Strike

100000

Flashing 1Hz

Flashing

Double Strike

Flashing Triple

Strike

101000

Flashing

1.5Hz

Flashing 2Hz

Flashing

Double Strike

010000

Flashing 2Hz

Flashing Triple

Strike

Flashing Triple

Strike

110000

Flashing

Double Strike

Steady High

Power

Flashing Triple

Strike

001000

Flashing

Triple Strike

Flashing 2Hz

Flashing

Double Strike

Warning – high-intensity light source. Avoid
looking directly at the light source for
extended periods of time.

End of Line
Resistor

Summary of Contents for BExCBL2-L2D-P













Search results

Summary of Contents for BExCBL2-L2D-P

Reviews:

Related manuals for BExCBL2-L2D-P

Brands by name

Popular brands

E2S BExCBL2-L2D-P, Instruction Manual

Search results

Summary of Contents for BExCBL2-L2D-P

Reviews:

Related manuals for BExCBL2-L2D-P

Brands by name

Popular brands