E2S BE S120D Series Instruction Manual Download Page 6

_______________________________________________________________________________________________________________________________ 

European Safety Systems Ltd.

   Impress House, Mansell Road, Acton, London W3 7QH           [email protected]              Tel: +44 (0)208 743 8880 

                                                                                                                                                             www.e-2-s.com             Fax: +44 (0)208 740 4200 
Document No. D210-00-011-IS           Issue 5          20-04-2020                         Sheet 6 of 8                                                                                            

 

14) Settings 

 

14.1 

Tone Selection

 

 

The sounders have 32 different tones that can be selected for 
the  first  stage  alarm.  The  sounders  can  then  be  switched  to 
sound  second  and  third  stage  alarm  tones.  The  tones  are 
selected by operation of a DIP switch on the pcb for both DC 
and  AC  units.  The  tone  table  on  page  seven  shows  the 
switch  positions  for  the  32  tones  and  which  tones  are 
available  for  the  second  and  third  stages.  To  operate  the 
sounder  on  stage  one  simply  connect  the  supply  voltage  to 
the normal supply terminals (+ve and 

–ve for DC units, L and 

N for AC units). 

 

14.2 

Volume Control 

 

 

The output level of the BEx sounder can be set by adjusting 
the  volume  control  potentiometer  (see  Fig  9).  For  maximum 
output, set the potentiometer fully clockwise. 
 

 

BExS120D AC 

 

 

BExS120D DC 

 

Fig. 9 Location of Volume Control Potentiometer   

 

15) Maintenance, Overhaul & Repair 

 

Maintenance,  repair  and  overhaul  of  the  equipment  should 
only  be  carried  out  by  suitably  qualified  personnel  in 
accordance with the current relevant standards: 

 

EN60079-19 
IEC60079-19 

Explosive atmospheres - Equipment repair, 
overhaul and reclamation 

 

EN 60079-17 
IEC60079-17 

Explosive atmospheres - Electrical 
installations inspection and maintenance 

 

To  avoid  a  possible  ELECTROSTACTIC  CHARGE  the  unit 
must only be cleaned with a damp cloth. 

 

Units  must  not  be  opened  while  an  explosive  atmosphere  is 
present. 

 

If  opening  the  unit  during  maintenance  operations  a  clean 
environment must be maintained and any dust layer removed 
prior to opening the unit. 

 

Flameproof  threaded  joints  and  cemented  joints  are  not 
intended to be repaired. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Warning - High noise levels above 85dB(A) 
during  operation.  High  levels  of  noise  may 
cause  hearing  loss,  wear  suitable  ear 
protection when equipment is in operation.

 

Volume Control 
Potentiometer   

Volume Control 
Potentiometer   

Summary of Contents for BE S120D Series









Reviews: