E-Z-GO FLEET 1999, Technician'S Repair And Service Manual

Page: 96 / 188

FUEL SYSTEM
Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings
Choke System
The choke functions to make initial starting of the engine
easier in cold weather conditions. The choke plate
restricts the air flow into the carburetor which richens the
air/fuel ratio.
Choke Operation
Pull the choke knob out to operate the choke (Ref Fig. 2
on page H-2). Check that the cable operates smoothly
and that the cable returns when the knob is released.
The motion should be smooth throughout the entire oper­
ating range. If there is any binding or sharp bends, the
choke cable assembly must be replaced.
I
NOTE
I
Do not attempt to lubricate the choke cable.
·
·
Lubricant tends to retain dirt on the moving
parts which will cause premature deterioration of the cable.
FUEL SYSTEM COMPONENT SERVICE AND
REPLACEMENT
Choke Cable and Housing Removal
Tool List Qty. Required
Open end wrench, 1/2" ................................................ 2
Open end wrench, 7/8" ................................................ 1
Phillips screwdriver ...................................................... 1
Loosen the screw (9) attaching the carburetor choke
shaft to the inner choke cable (1) (Ref Fig. 2 on page H-
2). Remove the nuts (2) securing the outer choke cable
(3) to its bracket. At the seat panel, remove the nut (4)
and lock washer (5) securing the outer cable to the bezel
retaining bracket (6). Slide the nut, lock washer and
bezel retaining bracket over the choke cable. Remove
the choke cable assembly and bezel (7) from the vertical
seat support.
7
Fig. 2 Choke Cable Attachment
Choke Cable and Housing Installation
I
NOTE
I
In the following text, there are references to
�-
---�-
removing/installing bolts etc. Additional hard­
ware (nuts, washers etc.) that are removed must always be
installed in their original positions unless otherwise specified.
Non-specified torque specifications are as shown in the table
contained in Section 'A'.
Feed the choke cable assembly (8) through the hole in
the bezel (7) (Ref Fig. 2 on page H-2). Insert the cable
and bezel into the seat panel and install the bezel retain­
ing bracket (6), lock washer (5) and nut (4) finger tight.
Slide the threaded portion of the housing through the car­
buretor mounted bracket and attach the nuts (2) to the
choke cable housing finger tight. Pass the choke cable
through the choke arm swivel and tighten the swivel
screw (9) after being sure that the choke and choke knob
are both in the open position.
Adjust the position of the curved portion of the cable
housing to ensure that the cable does not contact the
belts or other moving parts. Check the cable to be sure
that there are no sharp bends or kinks in the cable before
firmly tightening the nuts at both ends of the cable.
Carburetor Service
Be sure that the ignition system is functioning correctly
before determining that servicing the carburetor is
required. Refer to ELECTRICAL section for ignition sys­
tem information.
_AWARNING_A
To
prevent an ignition
spark which could ignite
gasoline from the fuel
system, the negative battery cable must be removed
from battery (see Section 'B').
Carburetor Removal
Tool List Qty. Required
Socket, 10 mm, 1/4" drive ............................................ 1
Ratchet, 1 /4" drive ....................................................... 1
Extension, 3", 1 /4" drive .............................................. 1
Parallel jaw pliers ......................................................... 1
Straight blade screwdriver ........................................... 1
Phillips screwdriver ...................................................... 1
Open end wrench, 9/16" .............................................. 2
Open end wrench, 3/8" ................................................ 1
Socket, 3/4", 3/8" drive ................................................ 1
Ratchet, 3/8" drive ....................................................... 1
Extension, 3", 3/8" drive .............................................. 1
Torque wrench, 3/8" drive, in. lbs ................................. 1
Page H-2
Repair and Service Manual