Med-Time
®
Components
Also included with your e-pill
system
(see below):
Doserin
g
Prescription
Styrk
Medicin
Läkare
Namn:
Nat
Midd
Morg
Kväll
Fre
Midd
Sön
Morg
Sön
Midd
Lör
Midd
Lör
Kväll
Lör
Natt
Fre
Kväll
Lör
Morg
Fre
Natt
Mån
Midd
Sön
Natt
Sön
Kväll
Mån
Morg
Fre
Morg
Tor
Kväll
Tor
Natt
Tor
Midd
Ons
Kväll
Tis
Midd
Tis
Kväll
Mån
Natt
Tis
Morg
Ons
Midd
Ons
Morg
Tis
Natt
Lör
Morg
Tis
Kväll
Ons
Morg
Lör
Kväll
Tor
Kväll
Fre
Morg
OnsKväll
Tor
Morg
Fre
Kväll
Lör
Morg
Sön
Morg
Mån
Kväll
Mån
Morg
Sön
Kväll
Tis
Morg
Tis
Kväll
Sön
Kväll
Mån
Morg
Lör
Kväll
Sön
Morg
Fre
Kväll
Tor Morg
Ons
Morg
Ons
Kväll
Tor
Kväll
Fre
Morg
Mån
Kväll
Tis
Morg
Ons
Natt
Prescription Card
Dosage Templates (2)
Extra Med-Tray with
dust cover
(4) AA Batteries
Keys (2)
Instructions
2
1. Lid with instructions
2. Display
3. Lock
4. Med-Tray
(two trays
supplied
with one
dust cover)
Programming Buttons 1, 2 and 3
Error Messages
If any fault or malfunction should occur with your Med-Time,
an ”
Err 2
” message should appear on the display. If you
receive this message, remove the batteries, re-program the
device as necessarry and
run the self-test
as described below.
If the fault cannot be corrected, contact your distributor.
Self Test
Med-Time has a built-in self test function.
Start Test
Make sure that the Medication Tray is in the device.
Press
button 1 for at least 10 seconds.
The CH message should
appear on the display.
To exit the test mode, press button 3.
When the display shows
CH
, Med-Time is ready to be tested.
To perform a system function test, press button 2
.
The unit will proceed through the following system test
modes:
”CH 1” Display Test: The display shows
CH 1
. All segments
on the display shall light up.
”CH 2” Rotation Test: The display shows
CH 2
. The motor
shall rotate the tray one compartment.
”CH 3” Alarm Signal Test: The display shows
CH 3
. The
alarm should sound. Turn the Med-Time over to test reset
function (as to dispense medicine). The signal should stop. The
CH 4
message will appear on the display if Med-Time is not
turned over within 30 seconds.
If the dispenser does not rotate properly the motor will stop
after a few seconds and display the error message ”
CH 6”
.
After a few seconds, Med-Time will return to CH Stand by
mode.
Exit the test mode by pressing button 3.
Contact e-pill or AMAC if you encounter any problems with
your Med-Time unit.
